The PureFlow AirDog A4SPBD001 100GPH Air/Fuel Separation System for your 1998.5-2004 Dodge 5.9L Cummins provides the most effective technology designed specifically for diesel pickups to remove water, particulates, vapor and entrained air from diesel fuel. The AirDog is lift pump and filter system, that enhances the fuel delivery to your engine with a commercial duty system.
Your high performance diesel engine demands higher fuel flows. Yet higher fuel flows increase the vacuum at the fuel pump and agitation in the fuel tank. These factors generate additional air/vapor in the fuel system preventing your engine form producing maximum power and efficiency. Additionally, air/vapor can cause galling and pitting of the injector barrel/plunger assembly and also tip erosion. The AirDog eliminates air in the fuel that robs your engine of consistently greater performance and can also cause permanent damage to your injectors. The AirDog also provides the fuel pressures and flows your diesel engine needs to produce maximum power, any time, every time!
The Airdog works by pulling fuel from the fuel tank containing entrained air/vapor, particulate contaminates and unknown quantities of moisture. The fuel passes through the water separator which removes the water and large particulate contaminates. Then, the fuel with only entrained air/vapor and tiny particulate contaminates remaining, enters the fuel pump. Under positive pressure flow, the fuel passes through the fuel filter and the remaining particulate contaminates are caught and contained, the entrained air/vapor is also separated and returned to the tank. The clean fuel is now free of contaminants and water and flows at the proper pressures up to your engine. Each kit includes plumbing, hardware, wiring harness, mounting bracket and all components needed for installation.
100 GPH @ 15-17 PSI (Stock-500HP)
Removes Air & Water From Fuel
Increased Horsepower & Torque
Optimized Engine Performance
Improved Throttle Response
Increased Fuel Economy
Lifetime Limited Express Warranty
Application Note: This kit is designed for use on trucks that have the factory pump in the factory location. If your truck has the retro-fitted in-tank pump you must use the A4SPBD353 kit. (see related products below)
CA Residents: CARB E.O. Number on file - LEGAL for use in California.
Comes with everything you need to install the pump, I installed it with a Beans Deisel Sump and didnt have to buy and extra hardware at all. Comes with plenty of fuel line to make your own custom lines. The quick connect fittings are super easy to use and high quality. No frame drilling required for the install. Instructions are very detailed. Great product overall
David Fence (Imperial Beach, CA) | February 16th, 2020
Has everything you need to install the pup WOTHOUT drilling into the frame which I’m a big fan of! The quick releases included in the kit are very high quality and make it very easy to run and connect lines. The instructions are very clear and concise depending on your year Cummins.
The only two problems I had were originally I didn’t keep the factory return line installed because I didn’t think the factory fuel filter was doing to be utilized, however, with the Airdog installed there is TWO return lines. One from the Airdog to the tank using the T connector on the full tank fill line and one from the fuel filter/bowl up front through the factory draw straw assembly. That was in the instructions but not abundantly clear in some of the pictures. And finally I know a lot of guys that run the airdog with an after market fuel sump setup and it would be awesome if a “with fuel sump” instruction was added so there’s no confusion on how to run lines to the sump from the Airdog.
XDP continues to closely monitor the COVID-19 (Coronavirus) outbreak. As an integral part of the automotive supply chain, at this point all call centers and distribution centers remain fully operational to ensure we keep vital service components flowing to vehicles used in transport of goods and emergency response. To ensure the health of our employees, families, and customers, we have made the following procedural changes:
UPDATE: Effective 6/1 Customer Service resumes normal business hours of M-F 8:30 – 9:00pm EST.
Effective 3/18 we have decided to temporarily close both of our retail stores in NJ and NV.
Our technical sales team remains available Mon-Fri 8:30am-9pm and Saturday 10:30am-7pm EST.
All employees have been encouraged to follow the CDC's recommendations at home and in the workplace.
The circumstances of this virus are fast moving, as such, we will continue to update you with any further operational adjustments as needed. As always, we value your business and appreciate your patience as we manage this situation together.