Products Showing Parts for — {{ active_vehicle.name }}

No Results Showing Parts for — {{ active_vehicle.name }}
USD 165
Part #: BD1041460

BD-Power 1041460 Full Bore Exhaust Manifold

2001-2010 GM 6.6L Duramax
Part #: BD1041460
★★★★★ ★★★★★ 10 Reviews
$ $165.00
In-Stock
SHARE
Our Recommendations Compatible Products
Close
Scroll to View More

Description

The BD-Power 1041460 Full Bore Exhaust Manifold will restore the balance to your engines exhaust flow, reduce cylinder load and reduce exhaust gas temperatures. The factory driver side exhaust manifold in your 01-10 Duramax is pinched down to allow for steering shaft clearance that isn't even required! As a result, your exhaust flow is significantly disrupted. The BD-Power Full Bore Exhaust Manifold addresses this issue by maintaining internal bore size. Made from high-silicon ductile iron, the Full Bore is a direct, bolt-in replacement for the factory manifold and is even drilled and tapped to accept the most popular EGT probes.

Stock Exhaust Manifold:

  • Only flows 80% of the passenger side manifold
  • 3 cylinders only operate at 80% capacity & load others down
  • No access to measure exhaust temperature

BD-Power Exhaust Manfilold:

  • Contaings Exhaust Temperature Probe Port
  • Maintains consistent exhaust pressure and temperature on both sides of the engine
  • Flow matches the passenger side manifold and balances the engines exhaust pressure.

 Manifold gaskets not included. 

Additional Information

Install Sheet

Specifications

  • MFG. Number 1041460
  • Manufacturer Name BD-Power
  • Shipping Weight 12.00 lb.
  • Shipping Length 18 in.
  • Shipping Width 5 in.
  • Shipping Height 5 in.
  • Fuel Type Diesel
  • UPC 019025003361
  • Prop 65 WARNING: Cancer & Reproductive Harm - P65Warnings.ca.gov

Reviews

★★★★★ ★★★★★
4.50/5 Stars out of 10 Reviews
5
5
4
5
3
0
2
0
1
0
Auto repairs on the offensive
5
FlokiBear (California, MD) | June 30th, 2019
Just makes sense to put this part in, not to mention the Pyrometer hole making it easy to add the EGT probe from Edge. Had to soak the bolts in Kroil to get them to loosen up, after removing the manifold heat shield (only broke 2/4 bolts), driver side intercooler tube, tire still on. Also replaced the 11 bolts for it, including 2 studs with ARP’s, even though they haven’t made their way here yet. Intermediate level job, doesn’t take more than a few hours if you re-use the gasket, but I opted to replace them, also not available here yet, but XDP is always the first place I check. Order # 971796
BD-POWER Exhaust Manifold
5
mtorskey (Unknown) | October 23rd, 2006
Takes 2 to 3 hours to install in the driveway. I'm a certified automotive technician and this was the best exhaust upgrade for the dollar. Then you remove the O.E. manifold and look at the new one you'll under stand why this is a must have! The diesel even sounds more balanced.
duramax exhaust manifold
4
rvfool (Unknown) | October 29th, 2006
I like the quality and workmanship. It installed with no messing with bolt holds. I did not notice anything special with performance but I do not have anything unusal on the engine. The old manifold was really restricted conpare to BD manifold. I would get another for my next vechile.
Pages 1   2   3   4

Write a Review

Include Your Order Number For a Chance to Win a $100 Gift card

Overall Rating

Your Information

Email Address will not be made public.

Customer Photos

Customer Photos

See what others built Submit your photo

Questions and Answers

Ask XDP a Question about this product (Allow 24-48 hours for reply)

Most Popular Questions

Is this just a manifold for the drivers side?
View Staff Answer 
Answer

The BD-Power 1041460 Full Bore Exhaust Manifold covers only the driver side manifold. The factory driver side exhaust manifold in the 01-10 Duramax is pinched down. This pinch restricts the exhaust flow significantly and disrupts the balance of the engine. With the addition of this manifold you’ll match the passenger side flow and balances the engines exhaust pressure. * At this time this kit does not come with a manifold gasket. Currently the highest quality gasket is the GM gasket.

will the edge egt probe fit in the port on this manifold
View Staff Answer 
Answer

Yes, an Edge Products EGT probe will fit into BD-POWER 1041460 FULL BORE EXHAUST MANIFOLD.

Emissions Notice

This product is not legal for sale or street use in California. Certain aftermarket products are subject to governmental emission standards regulated by the California Air Resources Board. In order for these products to be legal on a specific vehicle in California, the part number must receive a CARB Executive Order (EO) number. This number makes the part legal for use only on specific years, makes and models of vehicles. A decal with CARB EO number for these parts must be displayed in the engine bay to satisfy smog inspection requirements.