The ATS 2029064248 Electronic Fuel Regulator for your 2001-2010 GM 6.6L Duramax prevents over boost codes and defueling of the engine due to higher boost pressures. The ATS Electronic Fuel Regulator is an essential component when installing aftermarket modifications such as performance programmers and fueling upgrades.
Eliminates Over-Boost Codes
Easy Plug and Play Installation
Auto Meter 5323 OBDII Splitter340391.00
Use multiple OBDII devides with the Auto Meter 5323 OBDII Splitter. This low profile OBDII Signal Splitter / Pass Through allows for remote location of connections for OBDII products like the Auto Meter AirDrive, DashLink and Dash Control while providing an easy to access connection point for other onboard devices requiring access to the OBDII data stream.
Allows For Multiple OBDII Devices
Compatible With Most 1996+ OBDII Vehicles
BD-Power 1030710 2Low UnLoc323011.00
The BD-Power 1030710 2Low UnLoc provides your 2001-2014 GM 2500HD/3500HD with the option of low range in 2WD! The 2Low Unloc is designed to allow the operator to manually disable the front wheel drive mechanism by holding the hubs in the free (2WD) mode with the transfer case in 4WD low range. By allowing the front wheels to be disengaged, maximum torque is available to the rear wheels. This will also allow for sharp All The Way Over turns without the front axle u - joint hopping or binding.
With this kit installed, the front wheels will NOT be driven through the transfer case. This allows the operator to have full power and torque while in a high gear reduction applied to the rear axle only.
Enables Low Range 2WD
Applies Maximum Torque To Rear Axle Only
2001-2014 GM 2500HD/3500HD 4WD
2001-2013 GM 1500 4WD BD-Power 1036600 High Idle Switch9561.00
The BD-Power 1036600 High Idle Switch for your 01-04 GM 6.6L Duramax LB7 is an adjustable switch that will activate the high-idle mode on your truck. Perfect for use in cold weather or in applications where a PTO is needed, this switch taps into factory wiring and provides multiple idle speeds. Fits automatic transmissions only. Features: Faster Engine Warm-Up Great For PTO ApplicationsIdle From 800 RPM To 1800 RPM BD-Power 1057725 Staging Limiter213252.00
Get the perfect launch out of your 2001-2005 GM 6.6L Duramax with the BD-Power 1057725 Staging Limiter. Easily installed, the Staging Limiter allows you find the ideal settings for your Turbo Boost or Engine RPMs, so you are operating at the perfect level when the lights turn green. Whether you have been racing for years, or you’re preparing for your first race, the BD Power Staging Limiter will get you off the starting line at peak performance. After finding the perfect settings for your Turbo Boost or Engine RPMs, the Staging Limiter allows you to simply hold both the brake and throttle while preparing to launch. Once your brake is no longer depressed, your truck will launch smoothly. Features: Easy Install Consistent 1/4 Mile Times Eliminates Over and Under Boosts BD-Power 1057735 Throttle Sensitivity Booster275141.00
The BD-Power 1057735 Throttle Sensitivity Booster increases throttle sensitivity, and reduces that laggy pedal feeling in your 2001-2005 GM 6.6L Duramax. Modern vehicles utilize an accelerator pedal position sensor to control engine fueling. Many of these vehicles respond slowly and have poor throttle sensitivity. Much of this is actually caused by the factory programming within the ECM. The BD Throttle Sensitivity Booster corrects this by making the pedal more sensitive and making the vehicle more responsive.
The Throttle Sensitivity Booster includes a wiring harness specially designed with factory style connections for a simple installation. With two modes to choose from, the Throttle Sensitivity Booster can be run on +50% and +100% modes.
Reduces Pedal Lag
Quicker Turbocharger Spool-Up
Instant Throttle Response Increase
Installs Easily With Factory Connections
Note:The 1057735 will not work with the BD-Power shift-on-the-fly Throttle Sensitivity Switch upgrade.
2001-2005 GM Silverado/Sierra 2500/3500 - 6.6L Diesel
2001-2004 GM Silverado/Sierra 1500/2500/3500 - All V8 gas engines (not 4.3L V6)
BD-Power 1081160 Cool Down Timer 28481.00
The BD-Power 1081160 Cool Down Timer 2 eliminates the problems of shutting your engine down after a heavy haul when the exhaust gas temperature (EGT) is above normal. This can result in turbo bearing damage, but now you can protect your turbo with BDs Cool Down Timer (CDT). The CDT works with any K-Type EGT probe commonly found in most pyrometer gauge kits and has adjustable shut down temperature setting. Plus, five-minute timeout and quick shut down functions.
The new design of the CDT adds increased troubleshooting ability and new installation features plus the ability to work with vehicle security alarms and in reducing regeneration of the DPF on 2008-up vehicles. Temperature shutoff requires the purchase of the EGT Probe (sold separately, see below).
Shut Down By Timer
Shut Down By Temperature (Requires Probe)
Avoid Turbocharger Damage
Works With Any K-Type EGT Probe (Sold Separately, See Below)
Application Note: Will not work on Push-Button start Ford Trucks.
BD-Power 1515940 Turbo Boost Builder253111.00
The BD-Power 1515940 Turbo Boost Builder for your 2001-2004 GM 6.6L Duramax LB7 allows you to get more performance out of your electronically controlled engine. Installed inline with the MAP sensor, the BD-Power Boost Builder intercepts the message to the ECM, preventing it from setting an overboost trouble code that can cost between 50-80 horsepower. BDs Boost Builders are a perfect match for engines with performance injector or turbo enhancements and non-boost control power modules.
Eliminates Over Boost Codes
Uses Factory Sealed Connectors
Compliments Turbocharger and Injector Upgrades
Bully Dog 40400-105 Universal OBDII Block257241.00
The Bully Dog 40400-105 Universal OBDII Block fits the Bully Dog WatchDog and GT Tuner. It can also be used with the HandS Performance Mini Maxx and Black Maxx Tuners.Bully Dog Sensor Station w/ Pyrometer Probe 40384137542.00
The Bully Dog Sensor Station is an add-on that allows you to read EGT's on your GT Tuner, PMT and Watchdog. Additional sensors such as thermocouples, speed sensors, boost sensors and liquid temperature sensors can also be added to monitor even more on your Bullydog Tuner! Note: Pyrometer probe is included, 40387 probe below is additional and not required unless replacement is needed or additional sensors are desired. Diesel Turbo Lifesaver CM1E Control Module341521.00
Protect your turbocharger and allow for proper cool-down with the Diesel Turbo Lifesaver CM1E Control Module. The Diesel Turbo Lifesaver is designed to automatically idle your engine and turn it off without needing the ignition key, thus saving the time and aggravation of waiting for the turbo to cool down.When you shut off a hot engine, the oil used to lubricate your turbocharger sits uncirculated and gets cooked into a carbon coating that builds up on your turbo shaft. Over time, this can cause your turbocharger to seize requiring you to spend thousands on repairs. The Diesel Turbo Lifesaver gives you the ability to adjust your engine run time from 1 to 250 minutes to allow for a proper cool down. It also features a built-in security feature to safeguard your vehicle and can be used as a pre-luber in some applications to maximize the life of your engine. Features:Computer Controller For Precision TimingBuilt-In Anti-Theft Security Feature 3-Year Unlimited Mileage Warranty Made In The USA!Note: Control module only, required install kit is not included. See related items for specific applications. Installation Kit Guide: 1994-2002 Dodge Diesel Pickups (Use D1K Installation Kit)2003-2005 Dodge Diesel Pickups (Use D2K Installation Kit) 2006-2008 Dodge Diesel Pickups (Use D3K Installation Kit)1994-1997 Ford Diesel Pickups (Use F1K Installation Kit)1999-2004 Ford Diesel Pickups (Use F1AK Installation Kit)2005-2007 Ford Diesel Pickups (Use F2K Installation Kit)2008 Ford Diesel Pickups (Use F3K Installation Kit)1999-2001 Ford Doorlock Interface Kit (Use F1 and F1AK Kit)1999-2002 Ford Factory Alarm Interface Kit (Use F2 and F1AK Kit)2001-2007 GM Duramax Pickups (Use G1K Installation Kit) Diesel Turbo Lifesaver G1K Install Kit2672.00
Use the Diesel Turbo Lifesaver G1K Install Kit to easily install the Diesel Turbo Lifesaver on your 2001-2007 GM 6.6L Duramax. Diesel Turbo Lifesaver allows you to set an engine idle sequence to properly cool your turbocharger before engine shutdown. CM1E Turbo Timer Module is required for use and sold separately. Features: Installation Kit Works With CM1E Module (Sold Separately) Duramax Tuner DSP5 Switch146861.00
Standard DSP5 switch includes wiring, pins, conduit, hex key, knob and Duramax Tuner knob plate for use with DSP5 tuning.
For Use With DSP5 Tuning
Available in Standard Or Locking Switch
Edge Products 28855-D Amp'd Throttle Booster343851.00
Reduce the laggy pedal feel in your 2001-2005 GM 6.6L Duramax with the Edge Products 28855-D Amp'd Throttle Booster. The Edge Products Amp'd Throttle Booster gives you a night and day difference in your driving experience. Designed for an easy installation, the Throttle Booster is an easy way to get a "seat of the pants" power increase that you won't find anywhere else. Decreasing pedal lag expedites your vehicle's performance curve to occur sooner and supplies quicker turbocharging spooling. Amp’d features an intuitive plug-and-play installation using your vehicle’s stock connections. What makes Amp’d even more fun? Settings are adjustable to boost throttle position signals by 50% or 100%. Add in the optional Amp'd switch today and take throttle sensitivity to the next level with an additional 4 settings! FeaturesQuicker Spool-Up Improved Throttle Sensitivity Reduces Laggy Pedal Feeling Optimized Driving For In-Town and Highway Edge Products 88800 Amp'd Throttle Booster Switch343581.00
Add the Edge Products 88800 Amp'd Throttle Booster Switch to your Amp'd Throttle Sensitivity Booster for complete throttle control! The Amp'd switch enables 6 total power levels, as opposed to just 2 levels. The switch is a value-oriented upgrade that really creates a complete user-controlled experience for any type of driving preference.Features:6-modes Push button control Stock, Low-50%, Medium-75%, High-100%, Valet, and 400% "Wow Mode" Note: This switch works on All Amp'd Throttle Sensitivity Boosters.Edge Products 98202 Back-Up Camera12456.00
Xtreme Diesel Performance is an Authorized MVP dealer. We would like you to shop with confidence knowing your purchase is covered by the manufactures warranty.
The Edge Products 98202 Back-Up Camera is designed to work with the Edge Products CTS and CTS2 Monitors (not included) that have a built-in video port allowing you to connect Edge's state-of-the-art back-up camera. The CTS/CTS2's high resolution, color screen allows users to see what's going on behind them with the Edge camera connected to their existing CTS/CTS2. The camera mode automatically engages when the vehicle goes into reverse*. The back-up camera option is a must have for towers and safety-conscious drivers.
Durable Black Metal Finish
Adjustable Camera Angle
Parking Guide Lines
Night Vision LED's
Quick and Easy Installation
Reverse/Non-Reverse Image Switch (option)
Fits CTS and CTS2 Monitors (sold separately)
*Camera automatically engages on most supported vehicles with automatic transmission, it will not automatically engage on manual transmission modelsEdge Products 98609 EAS Power Switch w/ Starter Kit198722.00
The Edge Products 98609 EAS Power Switch is an excellent upgrade for anyone that has or is planning to get an Edge Products CTS. This power switch wiring harness gives you the ability to install accessories such as lights or an air compressor and engage them from the CTS. Due to the easily customizable software you can name your accessory right on the screen and power your accesory right from your CTS Monitor.
Control Accessories From CTS
Easy To Install and Operate
Includes EAS Power Switch w/ Starter Kit
Edge Products 98615 EAS 12V Power Supply Starter Kit280961.00
The Edge Products 98615 EAS 12V Power Supply Starter Kit allows the Insight CS2 and CTS2 to work on vehicles that don't have an OBDII port! By connecting to a key-switch power and ground source, an Insight becomes a digital gauge display for anything that you want to monitor! With the separate purchase of the EAS system, you can monitor EGTs, pressure readings, temperature readings, and much more.
12V Harness For Non-OBDII Applications
Works With Edge Products Insight CS2 and CTS2
Edge Products 98616 EAS Control Kit280971.00
The Edge Products 98616 EAS Control Kit allows you to monitor EGT's and adds the power switch to control multiple accessories with an on/off digital power switch. The EGT probe is a sensor that allows users to monitor critical Exhaust Gas Temperatures to ensure added power is not creating excessive heat which, in turn, can cause engine damage. This kit is ideal for the daily diesel driver or if you are towing then it's a must have! Towing can put a lot of strain on the truck and make it run hot. Don't be left on the side of the road with an overheated truck because you didn't watch your Exhaust Gas Temperatures with the Edge EAS EGT.
The EAS Power Switch is a tremendous new feature for truck owners! Customers can now hook up accessories like aftermarket lights, air compressors, etc. and engage them from the CTS/CTS2 device. Install the new switch and either use Edge's MyStyle software to name your accessory or with the CTS2 rename those accessories right from your device. The CTS2 comes with an all-new screen layout that can monitor up to 6 gauges and 4 rocker switches for the ultimate control. Take advantage of Edge's clean EAS daisy chain link system to turn your truck's tools on/off.
For CTS and CTS2
Add Power Switch
EAS Starter Kit
EAS EGT Probe
EAS Power Switch
Edge Products 98617 EAS Competition Kit280982.00
The Edge Products 98617 EAS Competition Kit is the perfect option for those enthusiasts that want to maximize the use of their Edge Insight. The EAS Compeition Kit gives you the ability to monitor EGTs and add an additional 0-100 PSIg boost and -40F to 300F temp sensors for ultimate control. This kit is designed for those truck owners who have upgraded turbo or turbo's and other mods ,where the stock sensors just aren't enough anymore. This kit is ideal for trucks participating in dyno competitions, sled pulls, and drag racing.
The EAS EGT probe is a sensor that allows users to monitor critical Exhaust Gas Temperatures to ensure added power is not creating excessive heat which, in turn, can cause engine damage. This kit is ideal for the daily diesel driver or if you are towing then it's a must have! Towing can put a lot of strain on the truck and make it run hot. Don't be left on the side of the road with an overheated truck because you didn't watch your Exhaust Gas Temperatures with the Edge EAS EGT.
The EAS 0-100 PSIg Boost Sensor is the perfect sensor for an aftermarket turbo that can build more boost than the stock MAP sensor can read. Simply install this sensor, use MyStyle to set up the sensor, and have the ability to see what kind of boost you can build. Or maybe you are trying to fine tune your truck and need to install a drive pressure sensor or fuel pressure sensor the Edge 0-100 PSIg sensor is your answer.
The EAS Temperature Sensor is a -40F to 300F 1/8 NPT sensor that will allow you to monitor things like Transmission Temp., Differential/Axle Oil Temp., Oil Temp., Engine Coolant Temp., Air Intake Temp., Pre and Post Intercooler Temp., and many more. Another great solution for those with aftermarket accessories.
Additionally, Edge Products has updated their Data Logging Software to now export all data logs into a CSV (Excel) file to save and compare runs, view, graph and improve tuning. To view CSV data log files, you must use MyStyle software or export it from MyStyle software. These new releases make the Insight CS2 and CTS2 the industry leader in digital gauge/data logging for any enthusiast!
Fits Edge CS/CS2 and CTS/CTS2
Includes Multiple Sensors For Monitoring Vitals
EAS Starter Kit
EAS EGT Probe
EAS Universal 5 Volt
EAS 0-100 PSig Pressure Sensor
EAS -40F To 300F Temperature Sensor