Products Showing Parts for — {{ active_vehicle.name }}

No Results Showing Parts for — {{ active_vehicle.name }}

Nozzles, Fittings & Plumbing

New Product Filters!
AEM Water-Methanol Injection Filter 30-3003 4875 2.00 AEM Water-Methanol Injection Filter 30-3003
$ 28.49
The AEM Water/Methanol Injection Filter is an in-line filter that uses a micronic mesh screen to filter particulates as small as 40 microns. This allows a cleaner flow of water/methanol to be passed into the engine, not only protecting the internals of the engine itself, but also the working parts of the water/methanol pump, too. Run the AEM Water/Methanol Injection Filter in-line before the pump to protect both pump and engine. If you are using a Water/Methanol Injection System it may greatly increase pump life to use a water/methanol filter. The AEM Water/Methanol Injection Filter prevents foreign particles as small as 40 microns from clogging or damaging pumps, injection nozzles check valves or flow sensors. The AEM Water/Methanol Injection Filter uses fittings for use with 1/4" OD nylon tubing, so it fits most Water/Methanol injection kits on the market today! Features: Simple to install, takes less than a minute. Fits virtually every Water/Methanol system on the market. Polypropylene housing - rugged material that is compatible with high concentrations of methanol. Completely Serviceable Assembly - can be disassembled, cleaned and reused for a long service life. Stainless Steel mesh strainer - AEMs custom mesh strainer filters down to 40 microns - MUCH smaller than similar filters. Large Filtering Area assure long service life and does not significantly reduce flow. Micronic Mesh Screen out-performs sintered filters in both filtering and serviceability.
Banks Power 41512X Water-Methanol Injection Fittings 19320 1.00 Banks Power 41512X Water-Methanol Injection Fittings
$ 4.19
The best plumbing available is provided with the highest cross-sectional flow area of any system on teh market. EPDM seals are methanol compatible and can withstand 300 PSI at under-hood temperatures. Installed fittings have 360 degree swivel capability for full flexibility.
Banks Power 4508X Water-Methanol Injection Nozzle 19300 1.00 Banks Power 4508X Water-Methanol Injection Nozzle
$ 21.41
The brass injection nozzles are specifically designed for this applications to achieve optimal atomization of water or water-methanol over a wide pressure range. A large 5/8" wrenching hex makes installation a breeze, and a stainless steel screen is integral to keep debris out of the orifice. A range of sizes are available to custom-tailor system performance.
Banks Power 45281 Water-Methanol Injector Nozzle (100cc/min) 35850 1.00 Banks Power 45281 Water-Methanol Injector Nozzle (100cc/min)
$ 23.79
The Banks Power 45281 Water-Methanol Injector Nozzle (100cc/min) is specially designed to achieve optimal atomization of water-methanol over a wide pressure range. Constructed from brass, the large 5/8” wrenching hex makes installing the Banks Power Injection Nozzle simple. Features:Simple InstallationConstructed From BrassDesigned To Achieve Optimal Atomization Of Water-Methanol Over A Wide Pressure Range
Banks Power 45282 Water-Methanol Injector Nozzle (200cc/min) 35852 1.00 Banks Power 45282 Water-Methanol Injector Nozzle (200cc/min)
$ 23.79
Constructed from Brass, the Banks Power 45282 Water-Methanol Injector Nozzle (200cc/min) has been specially engineered to achieve optimal atomization of water or water-methanol over a wide pressure range. A large 5/8” wrenching hex makes installation a breeze and a stainless steel screen keeps debris of the orifice.Features:Simple InstallationConstructed From BrassDesigned To Achieve Optimal Atomization Of Water-Methanol Over A Wide Pressure Range
Banks Power 45284 Water-Methanol Injector Nozzle (400cc/min) 35853 1.00 Banks Power 45284 Water-Methanol Injector Nozzle (400cc/min)
$ 23.79
Upgrade your Banks Water-Methanol Injection System with the Banks Power 45284 Water-Methanol Injector Nozzle (400cc/min). The Banks Power Injection Nozzle is easily installed and is perfectly engineered to achieve optimal atomization of water or water-methanol over a wide pressure range. An all brass construction provides superior durability to the injection nozzle and a stainless steel screen keeps debris from damaging the orifice. Features:Simple InstallationConstructed From BrassDesigned To Achieve Optimal Atomization Of Water-Methanol Over A Wide Pressure Range
Banks Power 45286 Water-Methanol Injector Nozzle (700cc/min) 35854 1.00 Banks Power 45286 Water-Methanol Injector Nozzle (700cc/min)
$ 23.79
Easily install the Banks Power 45286 Water-Methanol Injector Nozzle (700cc/min) to your vehicle and improve your Banks Water-Methanol Injection System. Constructed from Brass, the stainless steel screen of the Injection Nozzle keeps out damaging debris. The Injection Nozzle is Specifically designed to achieve optimal atomization of water or water-methanol over a wide pressure range. Features:Simple InstallationConstructed From BrassDesigned To Achieve Optimal Atomization Of Water-Methanol Over A Wide Pressure Range
Banks Power 45288 Water-Methanol Injector Nozzle (1000cc/min) 35851 1.00 Banks Power 45288 Water-Methanol Injector Nozzle (1000cc/min)
$ 23.79
The stainless steel screen of the Banks Power 45288 Water-Methanol Injector Nozzle (1000cc/min) keeps debris out of the orifice for a clean injection. Each Banks Power Injection Nozzle made from Brass and is specially designed to achieve optimal atomization of water or water-methanol over a wide pressure range. A large 5/8” wrenching hex makes installation simple and easy. Features:Simple InstallationConstructed From BrassDesigned To Achieve Optimal Atomization Of Water-Methanol Over A Wide Pressure Range
Nitrous Express 80014 Triple D Nitrous Nozzle 33607 1.00 Nitrous Express 80014 Triple D Nitrous Nozzle
$ 78.98
The Nitrous Express 80014 Triple D Nitrous Nozzle gives you 3 separate nozzles for 3 separate stages. The NX Triple D nozzles lets you run 3 stages of dry nitrous, no reversion guaranteed. This nozzle can be used for water-methanol as well so can have nitrous and water-methanol in the same nozzle. When used in an NX direct port system, this nozzle ensures consistent cylinder-to-cylinder distribution making them the preferrec choice for high horsepower applications. Features: 1/8" NPT Allows 3 Stages Also Works With Nitrous and Water-Methanol Combinations
Snow Performance 1/8" Mounting Bung 1771 1.00 Snow Performance 1/8" Mounting Bung
$ 25.25
The Snow Performance Nozzle Mounting Bung is a weldable threaded bung that make installing your injector nozzle easier when using thin-walled intake tubing. Simply drill a hole in your intake tube and weld in the bung. Your nozzle then has a strong threaded connection that can be used with confidence. The Nozzle Mounting Bung can also be used in many other applications such as mounting a nitrous nozzle, or even a boost gauge hookup. Available in steel or aluminum to work with your aluminum or steel intercooler pipes or intake system. Features: 1/8" NPT Threads Easy Mounting For Custom Installations Works With Nitrous Nozzles, Boost Ports and More!
Snow Performance 40035 Low Level Indicator 2051 1.00 Snow Performance 40035 Low Level Indicator
$ 16.83
The Snow Performance 40035 Low Level Indicator is a float switch and indicator light that lets you know when your reservoir is running low on fluid. Simple to install and wire in any reservoir. #40030 comes mounted in which ever reservoir is purchased. If a kit is upgraded with a 7 Quart Reservoir, the level switch will be mounted in it. #40035 is unmounted and can be added to any plastic reservoir including factory windshield washer fluid tanks.
Snow Performance 40060 Solenoid Upgrade 2191 1.00 Snow Performance 40060 Solenoid Upgrade
$ 50.52
The Snow Performance 40060 Shut off solenoid is used when mounting the injection nozzle lower than the reservoir or if the reservoir is rear-mounted to prevent gravity flowing. It is also used to prevent siphoning when the injection nozzle is mounted after the throttle body or carburetor and is exposed to vacuum.
Snow Performance 40080 Bulkhead Fitting 1772 1.00 Snow Performance 40080 Bulkhead Fitting
$ 17.99
The Snow Performance 40080 Bulkhead Fitting is a metal bulkhead fitting that allows a safe pass through on a firewall or in a reservoir (like a factory washer fluid tank) with quick connects on both sides. Threaded body can be tightened down with nuts on both sides, or in plastic tanks can be threaded in with methanol resistant (GOOP brand recommended) sealant for a leak-free installation.
Snow Performance 40110 Nozzle Mounting Adapter 1773 1.00 Snow Performance 40110 Nozzle Mounting Adapter
$ 25.25
The Snow Performance 40110 Nozzle Mounting Adapter supplies you with a way to mount your injector nozzle into your silicone or rubber intake tube? Snow Performance now offers a Nozzle Mounting Adapter for those without metal intake tubes. Made from Delrin, the adapter is methanol resistant and highly durable. Installation is easy: simply drill a 3/4" hole using a spade bit, insert the inner adapter piece, and thread on the outer adapter nut.