Eliminate the low fuel pressure codes in your 2004.5-2010 GM 6.6L Duramax with the Attitude Performance 2001 Fuel Rail Plug. Machined in the USA from 304 stainless steel, the Attitude Performance 2001 replaces your factory fuel pressure relief valve. Once your truck is modified or performance tuning is added, the factory Fuel Pressure Relief Valve (FPRV) cannot handle the added pressures. In many cases, this causes diagnostic trouble codes and also drastically reduces performance. Features:Eliminates Low Fuel Pressure Trouble Codes304 Stainless Steel ConstructionMADE IN THE USA! Note: The stock o-ring must be re-used during installation. If you would like to replace it, please see the XD308 below. BD-Power 1040360 Relief Valve Shim Kit246121.00
The BD-Power 1040360 Relief Valve Shim Kit for your 04.5-10 GM 6.6L Duramax and 07.5-10 Dodge 6.7L Cummins is designed to modify your factory fuel pressure release valve (FPRV). Modifying your release valve will help reduce the amount of fuel that returns to the tank, while keeping more consistent pressures in the fuel rail.
Eliminates Low Pressure Codes
Modifies Factory Release Valve
Essential For High Performance Applications
Dorman 904-111 Water In Fuel (WIF) Sensor Wrench292681.00
The Dorman 904-111 Water In Fuel (WIF) Sensor Wrench is specially designed for the Water In Fuel (WIF) Sensor in your 2001-2011 GM 6.6L Duramax. This Wrench makes sensor replacement easy and improves results by protecting the sensor from commonly incurred damages during removal. This wrench is double sided to fit the OE and the Dorman WIF Sensors.
Rubber Coated Handle For Easy Grip
Works With 2001-2011 Water In Fuel (WIF) Sensor
Dorman 904-112 Air Bleeder Screw293151.00
The Dorman 904-112 Air Bleeder Screw is a replacement for a common failure item in your 2001-2010 GM 6.6L Duramax. Sold as a 5 pack for the shop, or DIY Duramax Owner, this Air Bleeder Screw fits in the filter housing and allows you to open it up, to remove air from the system.
Pack Of 5
Replaces GM Part#: 12642623
FASS DFD-4000 Duramax Fuel Filter Delete190091.50
The FASS DFD-4000 Duramax Fuel Filter Delete for your 2001-2016 GM 6.6L Duramax is for use after the installation of a FASS Fuel Air Separation System. Once installed the factory fuel filter is no longer needed and can be easily removed by using this Factory Fuel Filter Canister Delete. Because your Duramax fuel filter is located after the FASS filtration system you will still need to replace the factory filter every 5,000-8,000 miles. This filter delete kit will replace your now useless fuel filter with a spin on canister that will allow fuel to flow freely into the engine, saving you even more money. This spin on Fuel Filter Delete Kit is a perfect addition to your FASS Titanium diesel fuel pump and comes with all required hardware for a professional installation.Features:Installs In Place Of Stock Filter Allows For Unrestricted Fuel Flow To Engine Built-In Gauge Port For Fuel Pressure MonitoringEliminates Costs Associated With Changing Stock FilterNote: This product is ONLY for use on trucks that already have another form of filtration such as a FASS Titanium Series Fuel System. Fleece FPE-GM-FFPD-0110 Fuel Primer Bulb Sealing Kit804412.00
The Fleece FPE-GM-FFPD-0110 Fuel Primer Bulb Sealing Kit is an excellent addition to the fuel system on your 2001-2010 GM 6.6L Duramax. This primer bulb sealing kit is designed to eliminate the primer bulb that can leak once an aftermarket lift pump kit is installed into your truck. Also included in this kit is a 1/8” NPT port that can be used on a low-pressure fuel gauge or the port can be capped off the included NPT plug. Features:1/8” NPT PlugFuel Primer CapInstallation Hardware Billet Aluminum ConstructionLisle 34350 Water Sensor Wrench314431.00
Having the right tools makes all the difference when doing maintenance on your 2001-2011 GM 6.6L Duramax, that's why the Lisle 34350 Water Sensor Wrench is a must-have in the tool box of any Duramax owner. The factory Water Sensor or Water In Fuel (WIF) Sensor is built from plastic and has a unique 12-sided design that is easily damaged by ill-fitting tools like pliers, adjustable wrenches, and channel locks. The 34350 Water Sensor Wrench is designed to directly fit the Water Sensor on your truck eliminating damage and making filter changes a breeze.
Fits 12-Sided WIF Sensor
Eases Fuel Filter Changes
Eliminates Unnecessary Damage To WIF Sensor
Merchant Automotive 10010 Aluminum Air Bleeder Screw806470.40
Replace the damaged or broken plastic air bleeder screw in your 2001-2016 GM 6.6L Duramax with the Merchant Automotive 10010 Aluminum Air Bleeder Screw. This bleeder screw features 6061 aluminum construction and is then black anodized for durability. Features:O-Ring IncludedBlack Anodized Finish6061 Aluminum ConstructionPPE 113061017 Dual Fueler Race Valve442081.00
The PPE 113061017 Dual Fueler Race Valve (M20-1.5 to M14-1.5), included in the PPE Dual Fueler Kits for 2001-2016 GM 6.6L Duramax diesel engines.Features:M20-1.5 to M14-1.5Dual Fueler Race ValvePPE Billet Aluminium Air Bleeder Screw 51308100048681.00
The PPE Billet Aluminium Air Bleeder Screw 513081000 is a simple upgrade that can save you a headache in the future on your 2001-2016 GM 6.6L Duramax. Most people know that billet aluminum is a lot tougher than plastic and that toughness means fewer problems over the long haul. So, replace your fragile plastic factory air bleeder screw with the longer lasting billet aluminum PPE Air Bleeder Screw. Damage and distortion that comes naturally with a plastic unit from routine servicing will no longer be a problem because PPEs Air Bleeder Screw features a Nitrile O-ring and billet aluminum construction. It is even yellow anodized for added visibility.
Machined Air Channel On Threads To Bleed Air
Bio-Diesel Compatible Nitrile O-Ring
PPE CP3 Pump Inlet Fitting 11306050148631.00
Get the most fuel flow possible from your stock CP3 pump with this "high flow" PPE CP3 Pump Inlet Fitting. The key is the larger inner diameter of the PPE fitting, which allows fuel to flow 70% more efficiently than with the restrictive stock unit. With a greater volume of fuel available to it, the CP3 injection pump will be able to perform at its optimum capability.Features:Stainless SteelCARB E.O. D-701-27For Use With 3/8" Hose70% More Flow Over Stock
PPE CP3 Pump Inlet Fitting 113060601249731.00
The PPE CP3 Pump Inlet Fitting 113060601 for your 2001-2010 GM 6.6L Duramax allows you to get the most fuel flow possible from your stock CP3 pump with this "high flow" PPE CP3 Pump Inlet Fitting. The key is the larger inner diameter of the PPE fitting, which allows fuel to flow 70% more efficiently than with the restrictive stock unit. With a greater volume of fuel available to it, the CP3 injection pump will be able to perform at its optimum capability.Features:Stainless SteelCARB E.O. D-701-27For Use With 1/2" Hose 70% More Flow Over Stock For Use With 1/2" Hose
PPE Diesel WIF (Water in Filter) Wrench 51308000048402.00
PPEs Water Level Sensor Wrench does two important jobs and is the perfect fit for both! The big end is used to remove the Water In Fuel (WIF) filter sensor with ease while the small end of the wrench was literally made to fit the billet PPE Air Bleeder Screw.
With time and exposure, plastic WIFs becomes brittle, and though it is hard to see, they also have a minute taper to them. PPEs Water Level Sensor Wrench matches that taper perfectly allowing the sensor to be safely removed when it is time to replace the filter. It is by definition a two in one tool, and since it is made from polished Stainless Steel it will look great in your tool box too!
Fits and Safely Removes Factory Water In Filter Sensor
Polished Stainless Steel
Small End Fits Billet PPE Air Bleeder Screw
PPE Ported Fuel Rail Fitting 11307100046611.00
PPEs Ported Fuel Rail Fitting replaces the restrictive stock fitting. Our fitting increases fuel flow volume from the CP3 pump to the fuel rail simply by making the hole bigger. Adequate fuel flow is vital to producing maximum horsepower. With the increased flow, the Ported Fuel Rail Fitting, is recommended for both high performance and race applications. These fittings benefit both fuel rails, since the driver side fuel rail feeds the passenger side. Features:One or two fittings can be used simultaneouslyReduces fuel pressure drops that are caused by the restriction of the stock fuel rail fittingDriver side required, additional passenger side strongly recommended for race or Dual Fueler applications PPE Race Fuel Valve 11307300014172.00
The PPE Race Fuel Valve 113073000 for your 2004.5-2010 GM 6.6L Duramax and 2007.5-2016 Dodge 6.7L Cummins replaces stock or a shimmed pressure relief valve. This valve helps maintain fuel rail pressure during full throttle driving by completely blocking the pressure relief port (effectively deadheading the fuel rail). It eliminates low fuel rail pressure DTC codes P1093 or P0087 (low fuel rail pressure during power enrichment) that are caused by insufficient PRV spring pressure.Features:CARB E.O. D-701-12Solid Steel ConstructionHelps Maintain Fuel Pressure During Full Throttle DrivingNote: You will re-use your factory o-ring. If you choose to replace it, you purchase a replacement o-ring in the related products below. PPE Release Valve Shim Kit 11307200014251.00
More fuel pressure equals more power and with the PPE Release Valve Shim Kit, you get both. The Release Valve Shim Kit increases the pressure needed to "pop off" the pressure relief valve (PRV). This means that the available fuel rail pressure remains high during full throttle driving and reduces the fuel flow through the fuel return system. The PPE Release Valve Shim Kit eliminates low fuel rail pressure DTC codes P1093 or P0087 (low fuel rail pressure during power enrichment) and is recommended for high performance and/or race applications. (CARB E.O. D-701-32)
Additional InformationInstall SheetXDP Aluminum Air Bleeder Screw XD12993421.00
The XDP Aluminum Air Bleeder Screw XD129 is a quick and simple solution for replacing your weak plastic factory screw. Unlike the factory screw that will round off or break in cold weather the XDP Aluminum Air Bleeder Screw is made of T6 billet aluminum.
Made from Anodized T6 Billet Aluminum
Machined air channel on threads to bleed air
Slotted to work with aftermarket wrenches
Includes OE Quality Viton O-ring
MADE IN THE USA!
Warranty Info:Products manufactured by XDP carry a 1-Year warranty against defects in materials and craftsmanship. The Warranty is Limited to one (1) year from the date of sale and limited solely to the parts contained within the product's kit. Click Here for full warranty policy.XDP Duramax CAT Adapter with 1R-0750 Filter, Bleeder Screw & Spacer238233.00
The XDP Duramax CAT Adapter with 1R-0750 Filter, Bleeder Screw and Spacer XD171 is an easy way to upgrade the fuel filter on your 2001-2016 GM 6.6L Duramax. The durable anodized filter adapter simply threads on to the OEM Filter Head and allows you run the more efficient and less expensive CAT Filter on your truck. For an even easier filter change, we also include a filter head spacer to give you more clearance for filter changes, along with an aluminum bleeder screw to replace the factory supplied plastic version that is commonly damaged during routine maintenance.
Lower Cost Filter Replacements
No Modifications To Factory Fuel System Needed
MADE IN THE USA!
Kit Contents:Anodized Filter Adapter with O-RingsCAT 1R-0750 FilterXDP Aluminum Air Bleeder ScrewFuel Filter Head SpacerAll Required Hardware for InstallationWarranty Info:Products manufactured by XDP carry a 1-Year warranty against defects in materials and craftsmanship. The Warranty is Limited to one (1) year from the date of sale and limited solely to the parts contained within the product's kit. Click Here for full warranty policy.
XDP Duramax CAT Filter Adapter & Filter Delete O-Ring XD228326231.00
The XDP Duramax CAT Filter Adapter and Filter Delete O-Ring XD228 is a replacement O-Ring Seal for the XDP Duramax CAT Filter Adapter, or the XDP Duramax Fuel Filter Delete for your 2001-2016 GM 6.6L Duramax. While the original seal provides a long service life, having a replacement in your tool box is always a good idea. Many customers choose to replace it while rebuilding their fuel filter head, or freshening up other fuel system components as their truck ages.
This is the large O-Ring that goes on the top of the XDP Fuel Filter Delete, or XDP Duramax CAT Filter Adapter and seals up against the surface of your factory fuel filter head.
Includes (1) Large O-Ring
Fits XDP Duramax CAT Filter Adapter XD171
Fits XDP Duramax Fuel Filter Delete XD163
Warranty Info:Products manufactured by XDP carry a 1-Year warranty against defects in materials and craftsmanship. The Warranty is Limited to one (1) year from the date of sale and limited solely to the parts contained within the product's kit. Click Here for full warranty policy.XDP Duramax CAT Filter Adapter Wrench XD325348441.00
The XDP Duramax CAT Filter Adapter Wrench XD325 is the perfect addition to the XDP Duramax CAT Filter Adapter Kit XD171. Installation of the XD171 requires tightening the CAT Filter Adapter to the fuel filter head and in some cases, it can become difficult once your hands are covered in fuel, or if your strap wrench just doesn't get a good grip. The XD325 is a problem-solving spanner wrench that is CNC machined from billet aluminum to mate perfectly to the XDP CAT Filter Adapter. This wrench allows you to easily install and remove the CAT Filter Adapter for routine maintenance. Features:Black Anodized FinishCNC Machined Billet AluminumFits XDP XD171 CAT Filter Adapter Kit
Products manufactured by XDP carry a 1-Year warranty against defects in materials and craftsmanship. The Warranty is Limited to one (1) year from the date of sale and limited solely to the parts contained within the product's kit. Click Here for full warranty policy.
XDP continues to closely monitor the COVID-19 (Coronavirus) outbreak. As an integral part of the automotive supply chain, at this point all call centers and distribution centers remain fully operational to ensure we keep vital service components flowing to vehicles used in transport of goods and emergency response. To ensure the health of our employees, families, and customers, we have made the following procedural changes:
Effective 3/16 we have shifted Customer Service hours to 8:30 – 7:00pm EST. To ensure compliance with New Jersey’s recent curfew.
Effective 3/18 we have decided to temporarily close both of our retail stores in NJ and NV.
Our technical sales team remains available Mon-Fri 8:30am-9pm and Saturday 10:30am-7pm EST.
All employees have been encouraged to follow the CDC's recommendations at home and in the workplace.
The circumstances of this virus are fast moving, as such, we will continue to update you with any further operational adjustments as needed. As always, we value your business and appreciate your patience as we manage this situation together.