The Alliant AP0085 Injector Brush Kit is a must have item in the toolbox of any Ford Powerstroke or Duramax technician. The Alliant Injector Brush Kit provides you with the proper tools to clean the injector bore and seat while installing new injectors in your engine. Features:Cleans Injector Bore and Injector SeatFits 6.0L/6.4L and 6.7L Powerstroke, Duramax Engines and More (see below)Application Note:2003-2016 Ford 4.5L, 6.0L, 6.4L, 6.7L Powerstroke Engines2003-2014 Navistar VT365, VT275, MaxxForce 5 and 72001-2016 GM 6.6L Duramax Dorman 904-111 Water In Fuel (WIF) Sensor Wrench292681.00
The Dorman 904-111 Water In Fuel (WIF) Sensor Wrench is specially designed for the Water In Fuel (WIF) Sensor in your 2001-2011 GM 6.6L Duramax. This Wrench makes sensor replacement easy and improves results by protecting the sensor from commonly incurred damages during removal. This wrench is double sided to fit the OE and the Dorman WIF Sensors.
Rubber Coated Handle For Easy Grip
Works With 2001-2011 Water In Fuel (WIF) Sensor
Haynes 10331 Techbook191881.00
272 pages of Step-by-step instructions for repair and maintenance of all Chevrolet and GMC Trucks and Vans 2001 thru 2012 GM 6.6L Duramax diesel engines.
Table Of Contents
Tools and equipment
Diagnostic Trouble Codes (DTCs)
Engine repairs and overhaul
Fuel and engine management systems
Emissions control systems
Chapter 1: Maintenance
Chapter 2: Cooling system
Chapter 3: Fuel system
Chapter 4: Turbocharger and charge air cooler
Chapter 5: Engine electrical systems
Chapter 6: Emissions and engine control systems
Chapter 7: Engine in-vehicle repair procedures
Chapter 8: Engine overhaul procedures
Chapter 9: Troubleshooting
Chapter 10: Wiring diagrams
Lisle 22100 Duramax Flywheel Holder & Socket314473.00
The Lisle 22100 Flywheel Holder and Socket saves time by locking the flywheel at the transmission instead of having to remove the starter for water pump replacement.
On 2500 and 3500 pickups, remove metal spring-loaded inspection plate on the bottom of the transmission. Tool should slide into opening toward engine with the top of the tool engaging the teeth of the flywheel.
On 4500 and 5500 trucks, remove the rubber inspection cap on the bottom of the transmission. Insert the tool at the front of the opening to engage the flywheel and hand tighten bolt to hold tool in place. Use 36mm 12 point socket with 3/4" square drive to remove harmonic balancer bolt and retorque on installation. 36mm 12 point socket can also be used on axle nuts.
Fits Duramax Engines
Lisle 34350 Water Sensor Wrench314431.00
Having the right tools makes all the difference when doing maintenance on your 2001-2011 GM 6.6L Duramax, that's why the Lisle 34350 Water Sensor Wrench is a must-have in the tool box of any Duramax owner. The factory Water Sensor or Water In Fuel (WIF) Sensor is built from plastic and has a unique 12-sided design that is easily damaged by ill-fitting tools like pliers, adjustable wrenches, and channel locks. The 34350 Water Sensor Wrench is designed to directly fit the Water Sensor on your truck eliminating damage and making filter changes a breeze.
Fits 12-Sided WIF Sensor
Eases Fuel Filter Changes
Eliminates Unnecessary Damage To WIF Sensor
Merchant Automotive 10015 Fan Shroud Push Clip Retainers (4-Pack)283611.00
The Merchant Automotive 10015 Fan Shroud Push Clip Retainers are replacements for the factory retainer clips that commonly get lost, or destroyed while being unfastened. These are high-quality replacements that are sold in a pack of 4.
OE Style Replacement
Merchant Automotive 10219 Torque Converter T-Handle R&R Tool238002.00
The Merchant Automotive 10219 T-Handle Torque Converter RandR Tool for your 2001-2016 GM 6.6L Duramax allows you to simply thread the T-Handles into any GM torque converter using 10 x 1.5mm converter bolts to get a firm grip that makes it easier to install heavy converters in closed bell housings. Eliminates the danger of it slipping out of your hands or cutting your self on the bell housing.
10x1.5 Bolt Pattern
Allows For Easier Converter Installation
Merchant Automotive 10358 Fan Clutch Wrench238102.00
The Merchant Automotive 10371 Engine Seal Driver Kit for your 2001-2016 GM 6.6L Duramax is specially designed to correctly install the front and rear main seals in your engine. Kit includes tools for both front and rear seals.
Merchant Automotive 10521 Deluxe Injector Removal Tool295725.00
The Merchant Automotive 10521 Deluxe Injector Removal Tool greatly eases the removal of the injectors in your 2004.5-2010 GM 6.6L Duramax. Heavy carbon buildup on the head and injector tip can make the injector difficult to remove. This puller is designed to pull the injector straight and completely out of the head reducing injector and head damage. This kit includes all components required to remove the injector in one continuous pull reducing component damage and reducing service times.
Pulls Injector Straight
Reduces Potential For Injector and Head Damage
Merchant Automotive 10522 Fuel Rail Pressure Sensor Wrench295732.00
The Merchant Automotive 10522 Fuel Rail Pressure Sensor Wrench features a unique design that saves time when replacing the Fuel Rail Pressure Sensor in your 2006-2010 GM 6.6L Duramax. Removing and replacing the Duramax fuel rail pressure sensor switch is difficult when using standard wrenches and sockets. The sensor is mounted on the right fuel rail under the EGR Cooler. Using conventional wrenches and sockets, a tech needs to remove the EGR cooler and heat shield(s) to gain access to the sensor. This specially designed wrench allows access without removing the EGR cooler and heat shields.
Compact Head To Fit Tight Spaces
Unique Design Saves Time and Money
Swinging Handle For Increased Mobility
Merchant Automotive 10523 Turbo Vane Position Sensor Socket295742.00
The Merchant Automotive 10523 Turbo Vane Position Sensor Socket provides an easy and secure way to removing and replacing the Turbo Vane Position Sensor on your 2004.5-2016 GM 6.6L Duramax. Featuring a low profile design for tight spaces, this socket is slotted to accommodate the wiring harness attached to the sensor. Eliminate the risk of damaging these expensive sensors by replacing it with the proper tools.
Slot To Accommodate Wire
Removes Sensor Without Damage
Low Profile Design For Tight Spaces
Merchant Automotive 22110 Flywheel Lock238051.00
PPEs Water Level Sensor Wrench does two important jobs and is the perfect fit for both! The big end is used to remove the Water In Fuel (WIF) filter sensor with ease while the small end of the wrench was literally made to fit the billet PPE Air Bleeder Screw.
With time and exposure, plastic WIFs becomes brittle, and though it is hard to see, they also have a minute taper to them. PPEs Water Level Sensor Wrench matches that taper perfectly allowing the sensor to be safely removed when it is time to replace the filter. It is by definition a two in one tool, and since it is made from polished Stainless Steel it will look great in your tool box too!
Fits and Safely Removes Factory Water In Filter Sensor
Polished Stainless Steel
Small End Fits Billet PPE Air Bleeder Screw
ReadyLift 66-7822A Torsion Key Unloading Tool3239212.00
When it comes to safely loading an unloading GM truck torsion keys, nothing beats the ReadyLift 66-7822A Torsion Key Unloading Tool. Made from forged hardened steel, this tool makes removing and installing torsion keys safe and easier, allowing for adjustment or replacement of GM torsion keys in as little as 15 minutes per truck. The forged and hardened steel used in the construction of this tool has been lab tested for strength and safety and is okay for use with air tools. Can be used with Dodge and Ford trucks. Dodge Trucks require an adapter plate which is included with all Dodge ReadyLift Torsion Key kits.Features: Heavy-Duty Design Forged Hardened Steel Allows Easy Removal Of Torsion KeysXDP - Xtreme Diesel Performance Funnel347541.00
Whether you're topping off the engine oil in your diesel, or filling your radiator, the XDP - Xtreme Diesel Performance Funnel is the right tool for the job. A useful tool, at a bargain of a price. Buy a few and put one in your truck toolbox, trailer, and shop!Features:For Easy PouringMolded Plastic ConstructionXDP 1/8" NPT Drill and Tap Kit XD196287201.00
Take the hassle out of drilling and tapping with the XDP 1/8" NPT Drill and Tap Kit XD196. Not having the right tools, or having to go find them, can waste a ton of time and really put a damper on the install of your newest upgrade. Installing a pyrometer probe to measure your exhaust gas temperatures? Installing a nozzle for your new nitrous or water-meth injection system? We've got you covered!
Each kit includes a 1/8" - 27 NPT high carbon steel taper pipe tap and a high-quality matching drill bit. Grab one of these kits when installing gauges, performance electronics that require EGT probes, and any other sender, probe or nozzle that requires 1/8" NPT threads.
1/8" - 27 NPT Tap and Bit
Perfect For EGT Probes and More
Resharpenable Drill Bit For Multiple Uses
XDP Custom Fender Cover XD372610032.00
The XDP Custom Fender Cover XD372 offers the ultimate in paint protection when wrenching on your truck. Manufactured from a high-quality PVC foam padding to protect the finish from chips, scratches, and dings. The anti-slip design helps to grip and hold your tools in place. 100% washable and resistant to most petroleum-based chemicals like oil, brake fluid, and coolant.This heavy-duty fender cover measures 22" x 34", and features the XDP Logo so you can show off your XDP pride!Features:22" x 34" DimensionsXDP Logo Featured on the SideManufactured from PVC Foam Padding Anti-Slip Design Helps Prevents Sliding XDP Duramax WIF (Water in Filter) Wrench XD12893271.00
The XDP WIF wrench XD128 is a must have for any GM Duramax owner, it makes removing and replacing your factory water in fuel sensor a breeze. The XDP WIF Wrench is specifically designed for the 12 sided plastic water sensor that is easily damaged by tools, like pliers, that do not specifically fit the sensor. As an added bonus the opposite side of the wrench is slotted to remove the plastic air bleeder screw with ease, preventing possibly rounding off the screw head.FEATURES:Precision machined 12 sided wrench perfectly fits stock water in fuel sensorHigh Quality T-6061 AluminumBlack Anodized Finish with engraved XDP logoBleeder screw driver on the opposite endMADE IN THE USA!Warranty Info:Products manufactured by XDP carry a 1-Year warranty against defects in materials and craftsmanship. The Warranty is Limited to one (1) year from the date of sale and limited solely to the parts contained within the product's kit. Click Here for full warranty policy.XDP Injector Brush Kit XD376443011.00
The XDP Injector Brush Kit XD376 helps clean the injector bore and seat when replacing the injectors in your Powerstroke or Duramax. Specially designed brushes help eliminate carbon deposits, rust and debris without damage. The XDP injector brush kit is a must for anyone swapping injectors!Brushes feature comfortable ABS plastic handles for long lasting durability. Each kit includes one Spiral Tube Brush and one Bottom Brush.Features:Cleans Injector Bore and SeatRemoves Carbon Deposits, Rust and Debris Without DamageFor use with Ford 6.0L/6.4L and 6.7L Powerstroke and GM 6.6L Duramax Engines Application Note:2003-2016 Ford 4.5L, 6.0L, 6.4L, 6.7L Powerstroke Engines2003-2014 Navistar VT365, VT275, MaxxForce 5 and 72001-2016 GM 6.6L Duramax
Warranty Info:Products manufactured by XDP carry a 1-Year warranty against defects in materials and craftsmanship. The Warranty is Limited to one (1) year from the date of sale and limited solely to the parts contained within the product's kit. Click Here for full warranty policy.
XDP continues to closely monitor the COVID-19 (Coronavirus) outbreak. As an integral part of the automotive supply chain, at this point all call centers and distribution centers remain fully operational to ensure we keep vital service components flowing to vehicles used in transport of goods and emergency response. To ensure the health of our employees, families, and customers, we have made the following procedural changes:
Effective 3/16 we have shifted Customer Service hours to 8:30 – 7:00pm EST. To ensure compliance with New Jersey’s recent curfew.
Effective 3/18 we have decided to temporarily close both of our retail stores in NJ and NV.
Our technical sales team remains available Mon-Fri 8:30am-9pm and Saturday 10:30am-7pm EST.
All employees have been encouraged to follow the CDC's recommendations at home and in the workplace.
The circumstances of this virus are fast moving, as such, we will continue to update you with any further operational adjustments as needed. As always, we value your business and appreciate your patience as we manage this situation together.