Products Showing Parts for — {{ active_vehicle.name }}

No Results Showing Parts for — {{ active_vehicle.name }}

Tools/Shop & Books

New Product Filters!
Alliant AP0085 Injector Brush Kit 26652 1.00 Alliant AP0085 Injector Brush Kit
$ 57.55
The Alliant AP0085 Injector Brush Kit is a must have item in the toolbox of any Ford Powerstroke or Duramax technician. The Alliant Injector Brush Kit provides you with the proper tools to clean the injector bore and seat while installing new injectors in your engine. Features:Cleans Injector Bore and Injector SeatFits 6.0L/6.4L and 6.7L Powerstroke, Duramax Engines and More (see below)Application Note:2003-2016 Ford 4.5L, 6.0L, 6.4L, 6.7L Powerstroke Engines2003-2014 Navistar VT365, VT275, MaxxForce 5 and 72001-2016 GM 6.6L Duramax
Dorman 904-111 Water In Fuel (WIF) Sensor Wrench 29268 1.00 Dorman 904-111 Water In Fuel (WIF) Sensor Wrench
$ 8.08
The Dorman 904-111 Water In Fuel (WIF) Sensor Wrench is specially designed for the Water In Fuel (WIF) Sensor in your 2001-2011 GM 6.6L Duramax. This Wrench makes sensor replacement easy and improves results by protecting the sensor from commonly incurred damages during removal. This wrench is double sided to fit the OE and the Dorman WIF Sensors. Features: Rubber Coated Handle For Easy Grip Works With 2001-2011 Water In Fuel (WIF) Sensor
Haynes 10331 Techbook 19188 1.00 Haynes 10331 Techbook
$ 19.95
272 pages of Step-by-step instructions for repair and maintenance of all Chevrolet and GMC Trucks and Vans 2001 thru 2012 GM 6.6L Duramax diesel engines. Topics Covered Table Of Contents Tools and equipment Troubleshooting Diagnostic Trouble Codes (DTCs) Routine Maintenance Engine repairs and overhaul Cooling system Fuel and engine management systems Electrical system Emissions control systems Chapter 1: Maintenance Chapter 2: Cooling system Chapter 3: Fuel system Chapter 4: Turbocharger and charge air cooler Chapter 5: Engine electrical systems Chapter 6: Emissions and engine control systems Chapter 7: Engine in-vehicle repair procedures Chapter 8: Engine overhaul procedures Chapter 9: Troubleshooting Chapter 10: Wiring diagrams
Lisle 22100 Duramax Flywheel Holder & Socket 31447 3.00 Lisle 22100 Duramax Flywheel Holder & Socket
$ 36.58
The Lisle 22100 Flywheel Holder and Socket saves time by locking the flywheel at the transmission instead of having to remove the starter for water pump replacement. On 2500 and 3500 pickups, remove metal spring-loaded inspection plate on the bottom of the transmission. Tool should slide into opening toward engine with the top of the tool engaging the teeth of the flywheel. On 4500 and 5500 trucks, remove the rubber inspection cap on the bottom of the transmission. Insert the tool at the front of the opening to engage the flywheel and hand tighten bolt to hold tool in place. Use 36mm 12 point socket with 3/4" square drive to remove harmonic balancer bolt and retorque on installation. 36mm 12 point socket can also be used on axle nuts. Features: Locks Flywheel Fits Duramax Engines
Lisle 34350 Water Sensor Wrench 31443 1.00 Lisle 34350 Water Sensor Wrench
5 5 1
$ 6.97
Having the right tools makes all the difference when doing maintenance on your 2001-2011 GM 6.6L Duramax, that's why the Lisle 34350 Water Sensor Wrench is a must-have in the tool box of any Duramax owner. The factory Water Sensor or Water In Fuel (WIF) Sensor is built from plastic and has a unique 12-sided design that is easily damaged by ill-fitting tools like pliers, adjustable wrenches, and channel locks. The 34350 Water Sensor Wrench is designed to directly fit the Water Sensor on your truck eliminating damage and making filter changes a breeze. Features: Fits 12-Sided WIF Sensor Eases Fuel Filter Changes Eliminates Unnecessary Damage To WIF Sensor
Lisle 34900 Water Sensor Wrench (OEM Version) 31444 1.00 Lisle 34900 Water Sensor Wrench (OEM Version)
$ 6.97
Having the right tools makes all the difference when doing maintenance on your 2012-2016 GM 6.6L Duramax, that's why the Lisle 34900 Water Sensor Wrench is a must-have in the tool box of any Duramax owner. The factory Water Sensor or Water In Fuel (WIF) Sensor is built from plastic and is easily damaged by ill-fitting tools like pliers, adjustable wrenches, and channel locks. The 34900 Water Sensor Wrench is designed to directly fit the Water Sensor on your truck eliminating damage and making filter changes a breeze. Features: Eases Fuel Filter Changes Eliminates Unnecessary Damage To WIF Sensor
Lisle 34910 Water Sensor Wrench (Aftermarket Version) 31445 1.00 Lisle 34910 Water Sensor Wrench (Aftermarket Version)
$ 6.97
Having the right tools makes all the difference when doing maintenance on your 2012-2016 GM 6.6L Duramax, that's why the Lisle 34910 Water Sensor Wrench is a must-have in the tool box of any Duramax owner. The factory Water Sensor or Water In Fuel (WIF) Sensor is built from plastic and is easily damaged by ill-fitting tools like pliers, adjustable wrenches, and channel locks. The 34910 Water Sensor Wrench is designed to directly fit the Water Sensor on your truck eliminating damage and making filter changes a breeze. Features: Eases Fuel Filter Changes Eliminates Unnecessary Damage To WIF Sensor
Merchant Automotive 10219 Torque Converter T-Handle R&R Tool 23800 2.00 Merchant Automotive 10219 Torque Converter T-Handle R&R Tool
$ 18.99
The Merchant Automotive 10219 T-Handle Torque Converter RandR Tool for your 2001-2016 GM 6.6L Duramax allows you to simply thread the T-Handles into any GM torque converter using 10 x 1.5mm converter bolts to get a firm grip that makes it easier to install heavy converters in closed bell housings. Eliminates the danger of it slipping out of your hands or cutting your self on the bell housing. Features: 10x1.5 Bolt Pattern Allows For Easier Converter Installation
Merchant Automotive 10358 Fan Clutch Wrench 23810 2.00 Merchant Automotive 10358 Fan Clutch Wrench
$ 33.2
The Merchant Automotive 10358 Fan Clutch Wrench is specially designed to fit the Fan Clutch in your 2001-2016 GM 6.6L Duramax.
Merchant Automotive 10371 Engine Seal Driver Kit 23802 5.00 Merchant Automotive 10371 Engine Seal Driver Kit
$ 190
The Merchant Automotive 10371 Engine Seal Driver Kit for your 2001-2016 GM 6.6L Duramax is specially designed to correctly install the front and rear main seals in your engine. Kit includes tools for both front and rear seals.
Merchant Automotive 10391 WIF Wrench 23780 1.00 Merchant Automotive 10391 WIF Wrench
$ 18.95
The Merchant Automotive 10391 WIF Wrench for your 2012-2016 GM 6.6L Duramax LML is built to remove the delicate plastic sensor during fuel filter servicing. The wrench is precision machined from T-6061 Aluminum and tolerances are kept to a tight spec to even work on worn or already damaged sensors. Use the handy slot on the other end of the tool to fit the bleeder screw securely and prevent round off. Features: T-6061 Aluminum Construction Precision Machined To Tight Tolerances
Merchant Automotive 10523 Turbo Vane Position Sensor Socket 29574 2.00 Merchant Automotive 10523 Turbo Vane Position Sensor Socket
$ 49.95
The Merchant Automotive 10523 Turbo Vane Position Sensor Socket provides an easy and secure way to removing and replacing the Turbo Vane Position Sensor on your 2004.5-2016 GM 6.6L Duramax. Featuring a low profile design for tight spaces, this socket is slotted to accommodate the wiring harness attached to the sensor. Eliminate the risk of damaging these expensive sensors by replacing it with the proper tools. Features: Slot To Accommodate Wire Removes Sensor Without Damage Low Profile Design For Tight Spaces
PPE Diesel WIF (Water in Filter) Wrench 513080000 4840 2.00 PPE Diesel WIF (Water in Filter) Wrench 513080000
$ 22.49
PPEs Water Level Sensor Wrench does two important jobs and is the perfect fit for both! The big end is used to remove the Water In Fuel (WIF) filter sensor with ease while the small end of the wrench was literally made to fit the billet PPE Air Bleeder Screw. With time and exposure, plastic WIFs becomes brittle, and though it is hard to see, they also have a minute taper to them. PPEs Water Level Sensor Wrench matches that taper perfectly allowing the sensor to be safely removed when it is time to replace the filter. It is by definition a two in one tool, and since it is made from polished Stainless Steel it will look great in your tool box too! Features: Fits and Safely Removes Factory Water In Filter Sensor Polished Stainless Steel Small End Fits Billet PPE Air Bleeder Screw
ReadyLift 66-7822B Heavy-Duty Torsion Key Unloading Tool 27561 5.00 ReadyLift 66-7822B Heavy-Duty Torsion Key Unloading Tool
$ 149.95
The ReadyLift 66-7822B Heavy-Duty Torsion Key Unloading Tool is an extra large, and extra heavy-duty tool that works on all heavy-duty platform vehicles. Primarily designed for 2011+ GM HD Trucks, this tool takes the industry leading ReadyLift 66-7822A and nearly doubles its strength and thickness. This translates into superior performance when loading or unloading torsion keys on heavy-duty platform vehicles. These vehicles require an extreme tool to deal with the extreme loading/unloading forces of torsion keys. The 66-7822B is a professional grade tool that has been lab tested to guarantee premium and safe performance. It is intended for use on all 2011-UP GM HD trucks and other applications that require a heavy-duty tool to remove or install torsion keys. Features: Heavy-Duty Design Fits 2011+ GM HD Trucks and Other Applications Doubled Thickness and Strength Over Past Designs
XDP - Xtreme Diesel Performance Funnel 34754 1.00 XDP - Xtreme Diesel Performance Funnel
$ 1.5
Whether you're topping off the engine oil in your diesel, or filling your radiator, the XDP - Xtreme Diesel Performance Funnel is the right tool for the job. A useful tool, at a bargain of a price. Buy a few and put one in your truck toolbox, trailer, and shop!Features:For Easy PouringMolded Plastic Construction
XDP 1/8" NPT Drill and Tap Kit XD196 28720 1.00 XDP 1/8" NPT Drill and Tap Kit XD196
$ 16.95
Take the hassle out of drilling and tapping with the XDP 1/8" NPT Drill and Tap Kit XD196. Not having the right tools, or having to go find them, can waste a ton of time and really put a damper on the install of your newest upgrade. Installing a pyrometer probe to measure your exhaust gas temperatures? Installing a nozzle for your new nitrous or water-meth injection system? We've got you covered! Each kit includes a 1/8" - 27 NPT high carbon steel taper pipe tap and a high-quality matching drill bit. Grab one of these kits when installing gauges, performance electronics that require EGT probes, and any other sender, probe or nozzle that requires 1/8" NPT threads. Features: 1/8" - 27 NPT Tap and Bit Perfect For EGT Probes and More Resharpenable Drill Bit For Multiple Uses
XDP Duramax WIF (Water in Filter) Wrench XD128 9327 1.00 XDP Duramax WIF (Water in Filter) Wrench XD128
$ 18.95
The XDP WIF wrench XD128 is a must have for any GM Duramax owner, it makes removing and replacing your factory water in fuel sensor a breeze. The XDP WIF Wrench is specifically designed for the 12 sided plastic water sensor that is easily damaged by tools, like pliers, that do not specifically fit the sensor. As an added bonus the opposite side of the wrench is slotted to remove the plastic air bleeder screw with ease, preventing possibly rounding off the screw head.FEATURES:Precision machined 12 sided wrench perfectly fits stock water in fuel sensorHigh Quality T-6061 AluminumBlack Anodized Finish with engraved XDP logoBleeder screw driver on the opposite endMADE IN THE USA!Warranty Info:Products manufactured by XDP carry a 1-Year warranty against defects in materials and craftsmanship. The Warranty is Limited to one (1) year from the date of sale and limited solely to the parts contained within the product's kit. Click Here for full warranty policy.
XDP WIF (Water in Filter) Wrench XD247 33355 1.00 XDP WIF (Water in Filter) Wrench XD247
$ 18.95
A must have for any 2012-2016 GM 6.6L Duramax and 2013-2018 Dodge 6.7L Cummins owner, the XDP WIF Wrench XD247 makes it easy to remove and reinstall your factory Water In Fuel (WIF) Sensor. Using XDP's specially designed wrench eliminates the risk of damage to the WIF Sensor from tools like pliers and adjustable wrenches that easily round off the factory sensor. Constructed from billet aluminum, the XDP WIF Wrench features an anodized black finish for good looks, and long life. As an added bonus, the opposite side of the wrench is slotted to remove the Duramax bleeder screw with ease, also preventing the possibility of breaking or stripping the factory screw head which commonly happens using a screwdrivers. Features: High Quality T-6061 Aluminum Precision Machined To Fit Factory WIF Sensor Black Anodized Finish With Engraved XDP Logo Bleeder Screw Driver On Opposite End (For Duramax Models Only) Warranty Info:Products manufactured by XDP carry a 1-Year warranty against defects in materials and craftsmanship. The Warranty is Limited to one (1) year from the date of sale and limited solely to the parts contained within the product's kit. Click Here for full warranty policy.