Products Showing Parts for — {{ active_vehicle.name }}

No Results Showing Parts for — {{ active_vehicle.name }}

Airaid Intake Systems

New Product Filters!
Airaid 200-295 MXP Series Intake System 18223 13.00 Airaid 200-295 MXP Series Intake System
$ 399.99
The 2013-2016 GM HD family of trucks now boast more power and torque than ever before thanks to some refinements to the Duramax LML 6.6L powerplant. After extensive research and development, Airaid was able to unlock an impressive 29 additional horsepower and 55 lb-ft of torque for the 2013 trucks with a new MXP Cold Air Intake system. This bolt-on intake system delivers impressive power gains, lowers EGTS and improves fuel efficiency all at the same time. The new Airaid MXP Cold Air Intake includes a one-piece roto-molded cold air-box, a new module intake tube, and an enormous 1700-CFM washeable and reusable Premium Air Filter with our traditional oiled filter media. All AIRAID filters are hand-poured using a special urethane blend that prevents cracking and shrinkage in the most extreme conditions. The key difference with this kit is the location of the Mass Air Flow (MAF) sensors on the intake tube. By eliminating restrictions in the factory intake tube and optimizing the location of each sensor, AIRAID is able to deliver impressive power increases while maintaining proper air/fuel rations and lower EGT's without the need for aftermarket tuning! The new MAF sensor location requires the addition of a pigtail to extend the factory MAF sensor wiring. Featuring GM weatherpack connectors and oe quality construction, this supplied pigtail simply snaps into place and looks just like a factory piece. Features: Massive, Washable and Reusable 1700-CFM Air Filter Roto-Molded Intake Tube With Optimized MAF Sensor Locations One-Piece Roto-Molded Intake Box With Oversized Air Inlets +29HP and 55ft-lbs. of Tq. CARB EO# D-609-14
Airaid 200-335 MXP Air Intake System 81652 44.00 Airaid 200-335 MXP Air Intake System
$ 399.99
The Airaid 200-335 MXP Air Intake System features a simple to clean filter that delivers 11.92 HP at 3077 RPM for your 2017-2019 GM 6.6L Duramax L5P. This Air Intake System embodies the ultimate in AIRAID's cold air induction technology and offers higher levels of acceleration and horsepower gains for your GM truck. Featuring a one-piece roto-molded air box, this intake addresses all the shortcomings of the restrictive stock design. An Airaid premium air filter is housed inside the air box for excellent air flow and filtration. To ensure correct mass air flow readings and calibration, air is routed through a new air intake tube made of cross-linked, high-density polyethylene that was created using intensive computer modeling. Fresh air ducting is included in this MXP air intake system, which improves airflow and includes accommodations for the factory mass air sensor. This means you get a simple-to-install, yet very complex system to boost air flow while maintaining correct air-to-fuel ratios, obviating the need for post-installation calibration. This air intake system comes with a warranty. The Airaid No Hassle Lifetime Warranty covers this air intake system for the life of your truck.Features:C.A.R.B. EO# D-609-20 High Airflow Premium Air FilterWashable and Reusable Air Filter MediaHorsepower Gain Of 11.92 HP At 3077 RPMEasy To Install Using Commonly Available ToolsReplaces Stock Intake Tubing, Air Filter and Air BoxAir Filter Is Protected From The Engine Compartment Hot AirNo Hassle Lifetime Warranty
Airaid 201-295 MXP SynthaMax Dry Filter Intake System 18224 13.00 Airaid 201-295 MXP SynthaMax Dry Filter Intake System
$ 399.99
The 2013-2016 GM HD family of trucks now boast more power and torque than ever before thanks to some refinements to the Duramax LML 6.6L powerplant. After extensive research and development, Airaid was able to unlock an impressive 29 additional horsepower and 55 lb-ft of torque for the 2013 trucks with a new MXP Cold Air Intake system. This bolt-on intake system delivers impressive power gains, lowers EGTS and improves fuel efficiency all at the same time. The new Airaid MXP Cold Air Intake includes a one-piece roto-molded cold air-box, a new module intake tube, and an enormous 1700-CFM washeable and reusable Premium Air Filter with our SynthaMax, Non-Oiled filter media. All AIRAID filters are hand-poured using a special urethane blend that prevents cracking and shrinkage in the most extreme conditions. The key difference with this kit is the location of the Mass Air Flow (MAF) sensors on the intake tube. By eliminating restrictions in the factory intake tube and optimizing the location of each sensor, AIRAID is able to deliver impressive power increases while maintaining proper air/fuel rations and lower EGT's without the need for aftermarket tuning! The new MAF sensor location requires the addition of a pigtail to extend the factory MAF sensor wiring. Featuring GM weatherpack connectors and oe quality construction, this supplied pigtail simply snaps into place and looks just like a factory piece. Features: Massive, Washable and Reusable 1700-CFM Air Filter Roto-Molded Intake Tube With Optimized MAF Sensor Locations One-Piece Roto-Molded Intake Box With Oversized Air Inlets +29HP and 55ft-lbs. of Tq.
Airaid 201-335 Sythaflow MXP Air Intake System 81653 44.00 Airaid 201-335 Sythaflow MXP Air Intake System
$ 399.99
The Airaid 201-335 Sythaflow MXP Air Intake System give your 2017-2019 GM 6.6L Duramax L5P better throttle response and additional 11.92 HP at 3077 RPM. This Air Intake System is the pinnacle of AIRAID's cold air induction technology, providing your GM vehicle with increased acceleration and horsepower. This intake, which has a one-piece roto-molded air box, corrects all of the drawbacks of the restricted stock design. For optimal air flow and filtration, an Airaid premium air filter is placed inside the air box. Air is channeled through a new air intake tube constructed of cross-linked, high-density polyethylene that was designed utilizing extensive computer modeling to assure proper mass air flow measurements and calibration. This MXP air intake system features fresh air ducting, which increases airflow and accommodates the OEM mass air sensor. This means you'll receive a simple-to-install system that boosts air flow while maintaining proper air-to-fuel ratios, eliminating the need for post-installation calibration. This air intake system is covered by a manufacturer's guarantee. This air intake system is covered by the Airaid No Hassle Lifetime Warranty for the life of your truck.Features:C.A.R.B. EO# D-609-20 High Airflow Premium Air FilterWashable and Reusable Air Filter MediaEasy To Clean Oil-Free Synthetic Air FilterHorsepower Gain Of 11.92 HP At 3077 RPMEasy To Install Using Commonly Available ToolsReplaces Stock Intake Tubing, Air Filter and Air BoxAir Filter Is Protected From The Engine Compartment Hot AirNo Hassle Lifetime Warranty
Airaid 300-786 JR. Intake System 26244 8.00 Airaid 300-786 JR. Intake System
$ 249.99
The Airaid 300-786 JR. Intake System for your 2013-2018 Dodge Ram 6.7L Cummins combines the Airaid Module Intake Tube (MIT) and the Airaid Drop-In Oiled Filter to increase power and performance in your Cummins pickup. The Airaid JR. Intake Systems does this by optimizing the airflow to the engine by eliminating the restrictive portions of your factory intake - the paper filter and factory tube!You stock intake tube has obstructive sound-canceling baffles and undersized tube diameters, all of these significantly restrict airflow. Along with the paper filter that comes in your truck from the factory. The Airaid Modular Intake Tube (MIT) features a smoother, straighter design constructed of cross-linked high-density polyethylene for strength and resistance to heat transfer. As a simple bolt-in replacement, the Modular Intake Tube simply installs in place of your factory components with the included hardware.Also included is the Airaid Drop-In Replacement Filter. A high quality, high-flow filter that's constructed of reinforced polyurethane casings that are guaranteed not to crack or warp while maintaining a positive seal within the factory air box, this filter comes with the traditional Synthaflow oiled filter media. This media type is able to filter down to 4 microns without impeding airflow, and is washable and reusable. While it's a simple installation, these two upgrades combined allow the engine to breathe easier and run more efficiently.Features:Easy InstallationUses Factory Air Intake SystemSynthaFlow Traditional Oiled Filter MediaIncludes Modular Intake Tube (MIT) and Drop-In Filter For Factory Box
Airaid 300-986 Modular Intake Tube 26242 4.00 Airaid 300-986 Modular Intake Tube
$ 159.99
The Airaid 300-986 Modular Intake Tube for your 2013-2018 Dodge Ram 6.7L Cummins increases power and performance by targeting a major restriction in your intake system, the factory intake tube! The AIRAID Modular Intake Tubes (MIT) optimize airflow to the engine by replacing the restrictive factory intake tube. The factory tube has obstructive sound-canceling baffles and undersized tube diameters, all of which hurt airflow. Constructed of cross-linked high-density polyethylene for strength and resistance to heat transfer, AIRAID MIT kits help straighten and greatly improve airflow to the engine. MIT tubes are direct replacements for factory intake tubes; simply remove the factory tube and install the new one using the supplied hardware. The design provides better throttle response and additional horsepower along with better fuel economy.Features:Increased FlowIncreased PerformanceDirect Replacement For Stock Tube
Airaid 301-786 SynthaMax Dry Filter JR. Intake System 26243 8.00 Airaid 301-786 SynthaMax Dry Filter JR. Intake System
5.00 5 2
$ 249.99
The Airaid 301-786 SynthaMax Dry Filter JR. Intake Kit for your 2013-2018 Dodge Ram 6.7L Cummins combines the Airaid Module Intake Tube (MIT) and the Airaid SynthaMax Dry Filter to increase power and performance in your Cummins pickup. The Airaid JR. Intake Kit does this by optimizing the airflow to the engine by eliminating the restrictive portions of your factory intake - the paper filter and factory tube!You stock intake tube has obstructive sound-canceling baffles and undersized tube diameters, all of these signifcantly restrict airflow. Along with the paper filter that comes in your truck from the factory. The Airaid Modular Intake Tube (MIT) features a smoother, straighter design constructed of cross-linked high-density polyethylene for strength and resistance to heat transfer. As a simple bolt-in replacement, the Modular Intake Tube simply installs in place of your factory components with the included hardware.Also included is the Airaid Drop-In Replacement Filter. A high quality, high-flow filter that's constructed of reinforced polyurethane casings that are guaranteed not to crack or warp while maintaining a positive seal within the factory air box, this filter comes with the SynthaMax dry filter media. This media type is able to filter down to 4 microns without impeding airflow, and is washable and reusable. While it's a simple installation, these two upgrades combined allow the engine to breathe easier and run more efficiently.Features:Easy InstallationUses Factory Air Intake SystemSynthaMax Dry Filter Media - No Oil RequiredIncludes Modular Intake Tube (MIT) and Drop-In Filter For Factory Box
Airaid 400-279 MXP Air Intake System 81648 10.40 Airaid 400-279 MXP Air Intake System
$ 399.99
The Airaid 400-279 MXP Air Intake System has been dyno proven to add 12.1 HP at 2850 RPM in your 2017-2019 Ford 6.7L Powerstroke. This intake system is the pinnacle of Airaid's cold air induction systems, providing more power and acceleration for your high-performance diesel truck. This intake system begins with a one-piece roto-molded air box that corrects the limitations of the restricted original design. An Airaid premium air filter is installed within the air box to provide excellent air flow and filtration. Air is routed through a new air intake tube made of cross-linked, high-density polyethylene that was created using intensive computer modeling to provide the highest possible airflow. The built-in velocity stack in this intake system helps to increase airflow even more. This means you get a simple-to-install, yet very complex system to boost air flow while maintaining correct air-to-fuel ratios, obviating the need for post-installation calibration. Just install it and go!Features:High Airflow Premium Air FilterWashable and Reusable Air Filter MediaHorsepower Gain Of 12.1 HP At 2850 RPMEasy To Install Using Commonly Available ToolsReplaces Stock Intake Tubing, Air Filter and Air BoxNo Hassle Lifetime Warranty
Airaid 401-279 Sythaflow MXP Air Intake System 81649 10.40 Airaid 401-279 Sythaflow MXP Air Intake System
$ 399.99
The Airaid 401-279 Sythaflow MXP Air Intake System has an easy to clean oil-free filter that will add 12.1 HP at 2850 RPM in your 2017-2019 Ford 6.7L Powerstroke. This intake system is the apex of Airaid's cold air induction systems, giving your high-performance diesel vehicle greater power and acceleration. The intake system starts with a one-piece roto-molded air box that corrects the earlier design's shortcomings. Within the air box, an Airaid premium air filter is fitted to offer optimum air flow and filtration. Air is sent into the system through a new air intake tube constructed of cross-linked, high-density polyethylene that was designed using sophisticated computer modeling to ensure maximum airflow. This intake system's built-in velocity stack helps to boost airflow even further. This means you'll receive a simple-to-install system that boosts air flow while maintaining proper air-to-fuel ratios, eliminating the need for post-installation calibration. Install it and you are ready to go!Features:High Airflow Premium Air FilterWashable and Reusable Air Filter MediaEasy To Clean Oil-Free Synthetic Air FilterHorsepower Gain Of 12.1 HP At 2850 RPMEasy To Install Using Commonly Available ToolsReplaces Stock Intake Tubing, Air Filter and Air BoxNo Hassle Lifetime Warranty
Airaid 790-550 Air Filter Tune-Up Kit 21 1.00 Airaid 790-550 Air Filter Tune-Up Kit
$ 11.99
The Airaid 790-550 Air Filter Tune-Up Kit is uniquely formulated to clean without damaging the gauze filter media. Airaid Performance Oil Forms an additional line of defense against dirt without limiting airflow. Cleaning Intervals: Clean your Airaid filter every 30,000 to 50,000 miles for normal driving, and more often for off-road and heavy dust conditions. Check Annually: If your annual mileage is low, check filter once a year to see if oiling is needed. Use Only Airaid Solution: Airaid Cleaning Solution is the best product to clean your AirAid filter. Never use gasoline, detergents, steam cleaning or parts solvent. Oil After Cleaning: Your AirAid Premium Filter is pre-oiled and ready to use out of the package. Always oil your AirAid Premium Filter after each cleaning. Use only AirAid Filter Performance Oil. No transmission fluid, motor oil, diesel fuel, or light weight oils. DO NOT OVER OIL!
Airaid 800-316 SynthaFlow Direct-Fit Replacement Filter 2135 7.00 Airaid 800-316 SynthaFlow Direct-Fit Replacement Filter
$ 129.99
The Airaid 860-316 SynthaFlow Direct-Fit Replacement Filter is a drop-in replacement for your stock air filter in your 03-07 GM C4500/C5500 6.6L/8.1L Duramax. Constructed using the same premium materials used in our Cold Air Intake Kits, these filters offer significant improvements in air flow and filtration while being washable and reusable. Why throw money away on a paper filter each time the old one gets dirty when you can upgrade to a serviceable Airaid Premium Filter for often less than the cost of two stock replacements? Airaid Direct-Fit filters require no modifications and installation is as simple as replacing a stock filter. Features: Washable and Reusable Oiled "Wet" Filter Media Drop-In Replacement For Stock Filter Applications: CHEVROLET C4500 KODIAK 2003-2007 V8 6.6L, V8 8.1L CHEVROLET C5500 KODIAK 2003-2007 V8 6.6L, V8 8.1L GMC TOPKICK 2003-2007 V8 6.6L, V8 8.1L
Airaid 850-030 Direct-Fit Replacement Filter 81646 1.70 Airaid 850-030 Direct-Fit Replacement Filter
$ 59.99
The Airaid 850-030 Direct-Fit Replacement Filter is engineered as a drop-in replacement for your 2016-2021 GM Colorado/Canyon 2.8L Duramax LWN or 2015-2021 GM Colorado/Canyon 2.5L and 3.6L Gas. This filter is replacement for your truck’s paper air filter and is designed to improve horsepower, torque, and acceleration. With the added benefit of being washable and reusable, this filter is manufactured with multiple layers of filter media and provides significant improvements in air flow and filtration. Why waste money on a paper filters every time the old filter becomes dirty when you can upgrade to a serviceable AIRAID Direct-Fit Replacement Filter for a fraction of the price of two standard replacements? It only takes a few minutes for installation and is as easy as replacing your original filter.Features:Oiled Filter MediaWashable and ReusableGreat Filtration With Low RestrictionTakes Only A Few Minutes For InstallationStock Replacement Filter For Better Performance
Airaid 850-357 SynthaFlow Direct-Fit Replacement Filter 1303 4.00 Airaid 850-357 SynthaFlow Direct-Fit Replacement Filter
$ 69.99
The Airaid 850-357 SynthaFlow Direct-Fit Replacement Filter is a drop-in replacement for your stock air filter in your 2003-2018 Dodge 5.9L/6.7L Cummins or 2019-2020 RAM 2500/3500 6.4L Gas. Constructed using the same premium materials used in our Cold Air Intake Kits, these filters offer significant improvements in air flow and filtration while being washable and reusable.Why throw money away on a paper filter each time the old one gets dirty when you can upgrade to a serviceable Airaid Premium Filter for often less than the cost of two stock replacements? Airaid Direct-Fit filters require no modifications and installation is as simple as replacing a stock filter.Features:Washable and ReusableOiled "Wet" Filter MediaDrop-In Replacement For Stock FilterApplications:DODGE RAM 2500 PICKUP 2003-2007 L6 5.9LDODGE RAM 3500 PICKUP 2003-2007 L6 5.9LRAM 2500 PICKUP 2007.5-2019 L6 6.7LRAM 3500 PICKUP 2007.5-2019 L6 6.7L
AirAid 850-385 Drop-In Replacement Filter 80160 1.52 AirAid 850-385 Drop-In Replacement Filter
$ 59.99
The AirAid 850-385 Drop-In Replacement Filter is a high-flow direct fit replacement air filter for your Ford truck. This washable filter is able to be cleaned and reused and features a oiled cotton gauze media that offers improved flow and filtration over your stock paper filter. Features:Easy InstallationWashable And ReusableBetter Filtration and Better FlowApplication:2009-2021 Ford F-150 Gas2018-2021 Ford F-150 3.0L Powerstroke2008-2015 Ford F-450/F-550 Super Duty 6.8L Gas2008-2016 Ford F-250/F-350 Super Duty 6.2L/6.8L Gas
Airaid 850-447 Direct-Fit Replacement Filter 81650 3.90 Airaid 850-447 Direct-Fit Replacement Filter
$ 74.99
The Airaid 850-447 Direct-Fit Replacement Filter is a high flow replacement air filter for your 2014-2021 Ram 1500 3.0L EcoDiesel or 2002-2021 Dodge Ram 1500/2500/3500 Gas. By swapping out your truck's paper air filter with this filter, you can increase horsepower, torque, and acceleration. This filter is made up of numerous layers of filter material that enhances air flow and filtering while remaining washable and reusable. Why waste money on paper filters every time the old one becomes dirty when you can upgrade to a functional AIRAID Direct-Fit Replacement Filter for the price of two standard replacements? It simply takes a few minutes to install this filter, and it is as simple as changing your previous one.Features:Oiled Filter MediaWashable and ReusableGreat Filtration With Low RestrictionTakes Only A Few Minutes For InstallationStock Replacement Filter For Better PerformanceApplications:2020-2021 Ram 1500 3.0L Diesel2020-2021 Ram 1500 3.6L Gas2020-2021 Ram 1500 5.7L Gas2014-2019 Ram 1500 Classic 3.0L Diesel2013-2021 Ram 1500 Classic 3.6L Gas2009-2020 Dodge Ram 1500 Classic 5.7L Gas2002-2012 Dodge Ram 1500 3.7L Gas2002-2002 Dodge Ram 1500 3.9L Gas2002-2013 Dodge Ram 1500 4.7L Gas2002-2003 Dodge Ram 1500 5.9L Gas2003-2008 Dodge Ram 1500 5.7L Gas2003-2018 Dodge Ram 2500 5.7L Gas2014-2018 Dodge Ram 2500 6.4L Gas2003-2018 Dodge Ram 3500 5.7L Gas2014-2018 Dodge Ram 3500 6.4L Gas2014-2017 Dodge Ram 4500 6.4L Gas2014-2017 Dodge Ram 5500 6.4L Gas2007 Dodge Ram SRT-10 8.3L Gas2003 Dodge Ram 2500/3500 8.0L Gas
Airaid 851-030 Sythaflow Direct-Fit Replacement Filter 81647 1.70 Airaid 851-030 Sythaflow Direct-Fit Replacement Filter
$ 64.99
The Airaid 851-030 Sythaflow Direct-Fit Replacement Filter is an easy-to-clean reusable filter for your 2016-2021 GM Colorado/Canyon 2.8L Duramax LWN | 2015-2021 GM Colorado/Canyon 2.5L and 3.6L Gas. This filter is meant to enhance horsepower, torque, and acceleration by replacing your truck's paper air filter. This filter is made with multiple layers of oil-free filter material and delivers increases in air flow and filtration while also being washable and reusable. Why spend money on paper filters every time the old one gets filthy when you can upgrade to a serviceable AIRAID Direct-Fit Replacement Filter for the cost of two regular replacements? Installing this filter only takes a few minutes and is as simple as replacing your old filter.Features:Washable and ReusableGreat Filtration With Low RestrictionTakes Only A Few Minutes For InstallationEasy To Clean Oil-Free Red Synthetic Air FilterStock Replacement Filter For Better Performance
Airaid 851-223 SynthaMax Dry Direct-Fit Replacement Filter 20173 2.00 Airaid 851-223 SynthaMax Dry Direct-Fit Replacement Filter
$ 69.99
The Airaid 851-233 SynthaMax Dry Direct-Fit Replacement Filter is a drop-in replacement for your stock air filter in your 05-10 Jeep Grand Cherokee. Constructed using the same premium materials used in our Cold Air Intake Kits, these filters offer significant improvements in air flow and filtration while being washable and reusable. Why throw money away on a paper filter each time the old one gets dirty when you can upgrade to a serviceable Airaid Premium Filter for often less than the cost of two stock replacements? Airaid Direct-Fit filters require no modifications and installation is as simple as replacing a stock filter. Features: Washable and Reusable Oil-Free "Dry" Filter Media Drop-In Replacement For Stock Filter Applications: CHRYSLER 300 2005-2009 V6 2.7L, V6 3.5L, V8 5.7L DODGE CHALLENGER 2008-2009 V8 6.1L, V6 3.5L, V8 5.7L DODGE CHARGER 2006-2009 V6 2.7L, V6 3.5L, V8 5.7L, V8 6.1L DODGE MAGNUM 2005-2007 V6 2.7L, V6 3.5L, V8 5.7L, V8 6.1L JEEP COMMANDER 2006-2008 V8 5.7L JEEP GRAND CHEROKEE (WK) 2005-2010 V6 3.7L, V8 4.7L, V8 5.7L, V6 3.0L JEEP GRAND CHEROKEE (WK) (Canadian) 2009-2009 V8 5.7L JEEP LIBERTY (KJ) 2002-2007 V6 3.7L
Airaid 851-357 SynthaMax Dry Direct-Fit Replacement Filter 20169 4.00 Airaid 851-357 SynthaMax Dry Direct-Fit Replacement Filter
$ 69.99
The Airaid 851-357 SynthaMax Dry Direct-Fit Replacement Filter is a drop-in replacement for your stock air filter in your 2003-2018 Dodge 5.9L/6.7L Cummins or 2019-2020 RAM 2500/3500 6.4L Gas. Constructed using the same premium materials used in our Cold Air Intake Kits, these filters offer significant improvements in air flow and filtration while being washable and reusable.Why throw money away on a paper filter each time the old one gets dirty when you can upgrade to a serviceable Airaid Premium Filter for often less than the cost of two stock replacements? Airaid Direct-Fit filters require no modifications and installation is as simple as replacing a stock filter.Features:Washable and ReusableOil-Free "Dry" Filter MediaDrop-In Replacement For Stock Filter
AirAid 851-385 Synthaflow Direct-Fit Replacement Filter 80161 1.52 AirAid 851-385 Synthaflow Direct-Fit Replacement Filter
$ 74.99
Get more power and mileage out of your ford truck with the AirAid 851-385 Synthaflow Direct-Fit Replacement Filter. This dry media filter can be cleaned and reused and offers better flow and filtration over your stock paper filter. Features:Easy InstallationOil Free Filter MediaWashable And ReusableBetter Filtration and Better FlowApplication:2009-2021 Ford F-150 Gas2018-2021 Ford F-150 3.0L Powerstroke2008-2015 Ford F-450/F-550 Super Duty 6.8L Gas2008-2016 Ford F-250/F-350 Super Duty 6.2L/6.8L Gas
Airaid 851-447 Sythaflow Direct-Fit Replacement Filter 81651 3.90 Airaid 851-447 Sythaflow Direct-Fit Replacement Filter
$ 79.99
The Airaid 851-447 Sythaflow Direct-Fit Replacement Filter can enhance the performance of your 2014-2021 Ram 1500 3.0L EcoDiesel or 2002-2021 Dodge Ram 1500/2500/3500 Gas. You can enhance horsepower, torque, and acceleration by replacing your truck's paper air filter with this filter. This filter contains many layers of oil-free filter material that improve air flow and filtration while staying washable and reusable. Why throw money away on paper filters every time your old one gets filthy when you can upgrade to a functioning AIRAID Direct-Fit Replacement Filter for the cost of two regular replacements? Installing this filter takes only a few minutes and is as simple as replacing your existing one.Features:Washable and ReusableGreat Filtration With Low RestrictionTakes Only A Few Minutes For InstallationEasy To Clean Oil-Free Red Synthetic Air FilterStock Replacement Filter For Better PerformanceApplications:2020-2021 Ram 1500 3.0L Diesel2020-2021 Ram 1500 3.6L Gas2020-2021 Ram 1500 5.7L Gas2014-2019 Ram 1500 Classic 3.0L Diesel2013-2021 Ram 1500 Classic 3.6L Gas2009-2020 Dodge Ram 1500 Classic 5.7L Gas2002-2012 Dodge Ram 1500 3.7L Gas2002-2002 Dodge Ram 1500 3.9L Gas2002-2013 Dodge Ram 1500 4.7L Gas2002-2003 Dodge Ram 1500 5.9L Gas2003-2008 Dodge Ram 1500 5.7L Gas2003-2018 Dodge Ram 2500 5.7L Gas2014-2018 Dodge Ram 2500 6.4L Gas2003-2018 Dodge Ram 3500 5.7L Gas2014-2018 Dodge Ram 3500 6.4L Gas2014-2017 Dodge Ram 4500 6.4L Gas2014-2017 Dodge Ram 5500 6.4L Gas2007 Dodge Ram SRT-10 8.3L Gas2003 Dodge Ram 2500/3500 8.0L Gas