Products Showing Parts for — {{ }}

No Results Showing Parts for — {{ }}
USD 12.95
Part #: XD200

XDP Push Lock Fuel Pressure Tee XD200

Universal - 1/2" Push-Lock Fitting
Part #: XD200
★★★★★ ★★★★★ 4 Reviews
Buy now, pay later using Affirm Logo during checkout.
Our Recommendations Compatible Products
Scroll to View More


The XDP Push-Lock Fuel Pressure Tee XD200 is machined from aluminum with a pre-drilled & tapped 1/8" NPT port to accept a fuel pressure sender or hose. The 1/2 Push-Lock fitting makes it ideal for use with aftermarket fuel systems such as Airdog or FASS. Simply install this fitting in-line for a hassle-free fuel pressure gauge install.

  • 1/2" Push-Lock Fitting
  • 1/8" NPT Threads
Note: This Pressure Tee will not fit on the older FASS systems with 3/8" line.

Warranty Info:
Products manufactured by XDP carry a 1-Year warranty against defects in materials and craftsmanship. The Warranty is Limited to one (1) year from the date of sale and limited solely to the parts contained within the product's kit. Click Here for full warranty policy.


  • MFG. Number XD200
  • Manufacturer Name XDP
  • Shipping Weight 1.00 lb.
  • Shipping Length 8 in.
  • Shipping Width 8 in.
  • Shipping Height 2 in.
  • Fuel Type Diesel / Gas
  • UPC 857062006033
  • Warranty Yes
  • Warranty Info 1 Year / Unlimited Mileage
  • Prop 65 Prop 65 WarningWARNING: Cancer & Reproductive Harm -
  • Internal L50.00R6.00


Currently Viewing Reviews with a rating of 2. Click here to reset.
★★★★★ ★★★★★
4.0/5 Stars out of 4 Reviews
Worked alright.
This Push lock did make installing a fuel pressure sending unit easy However, Something was up with the treads. I notice that when screwing in the sending unit. It acted like it wanted to cross tread. So I got a tap and run it in and out a few times. Made it feel better but it sill didn't feel right. I had to have the sending unit pointing in just the right way for it to screw in buy hand and not feel like it was cross treading. After installing I primed the pump and notice a steady stream of fuel spraying out of the tee where the sending unit screws in all over the side of the engine. I got a wrench and tighten it down some more. still was leaking. I took it back off, put a little bit of Teflon pipe dope on the treads. Still leaked . So I tighten it down to the point where I was afraid any tighter it was going to pull the treads out of the tee. Still leaked But now it was only a dribble . At this point I was very frustrated, It was 1am and I needed the truck the next day. So I took it back apart, cleaned the pipe dope off. got some permatex thread sealant. Put it on the treads of the tee and the sending unit. Let it cure over night. Primed the pump and now no leaks. Over all I'm not very satisfied with this tee. It looks nice but I don't like the fact its a aluminum treads and the sending unit is steel. Id rather have a steel tee. That way you wouldn't have to worry as much about stripping treads out. maybe I just got a tee that wasn't drilled and taped quite right, But Id still would have some permatex thread sealant on hand just in case.

Write a Review

Include Your Order Number For a Chance to Win a $100 Gift card

Overall Rating

Your Information

Email Address will not be made public.

Customer Photos

Customer Photos

See what others built Submit your photo

Questions and Answers

Will this fit on my FASS 165 system?
View Staff Answer 
Yes, the XD200 (XDP PUSH LOCK FUEL PRESSURE TEE) will work just fine with any aftermarket fuel system that uses 1/2" fuel lines.
Is this considered a 8an fitting?
View Staff Answer 
Yes, an 8AN Equivalent Tube Size (Nominal OD) is 1/2".

Ask a question about this product

Please allow up to 1 business day for reply.

More to Consider

Recently Viewed